5.Connect the CONNECTOR (J) leading from the HANDLE- BAR ASSEMBLY (E) with the CONNECTOR (J) leading from the SEAT ASSEMBLY (F). Be sure the connectors fully lock.
CAUTION: To ensure that your handsensor heart rate works properly, secure the HEART RATE CABLE (K) into the CABLE TIE CLIPS (G). Note the routing of the HEART RATE CABLE so as to not pinch the HEART RATE CABLE between the SEAT and the SEAT ASSEM- BLY during assembly.
6.Locate the SEAT BOTTOM (L). Align the SEAT BOTTOM mounting holes with those in the LOWER SEAT SUPPORT TUBES (M). Secure the SEAT BOTTOM using four 2" PHILLIPS SCREWS (6) and LOCK WASHERS (7). Tighten the SCREWS securely.
7.Align the guide rollers located on the underside of the SEAT ASSEMBLY (F) with the SEAT EXTRUSION (N). Carefully guide the SEAT ASSEMBLY onto the SEAT EXTRUSION. Slide the SEAT ASSEMBLY fully forward. Connect the WIRE
(O) leading from the user left side of the SEAT ASSEMBLY to the jack located at the left front of the SEAT EXTRUSION.
8.In the hole located in the user right side of the SEAT EXTRU- SION (J), behind SEAT ASSEMBLY (F), install one
9.Mount the SEAT ADJUSTMENT LEVER (P) to the user right side of the SEAT ASSEMBLY (F) using two 3/4" PHILLIPS SCREWS (11). Tighten the SCREWS securely.
10.Secure the SEAT BACK (Q) to the UPPER SEAT SUPPORT TUBES (R) using four 2" PHILLIPS SCREWS (6) and LOCK WASHERS (7). Tighten the SCREWS securely.
11.Locate the SEAT EXTRUSION ENDCAP (S). Secure the SEAT EXTRUSION ENDCAP to the SEAT EXTRUSION (N) using two 1/2" PHILLIPS SCREWS (12).
12.Locate the MONOCOLUMN (T). Cut the WIRE TIE securing the WIRE (U) to the bottom of the MONOCOLUMN. Slide the MONOCOLUMN COVER (V) onto the MONOCOLUMN as shown. Slide the MONOCOLUMN COVER up to the
HANDLEBAR TUBE (W).
13.Locate and insert the GROMMET (X) into the SIDE ACCESS HOLE (Y) of the MONOCOLUMN (T). Pull the WIRE (U) out through the SIDE ACCESS HOLE.
14.With the HANDLEBAR TUBE (W) facing the rear of the unit as shown, slide the MONOCOLUMN (T) into the MONO- COLUMN BRACKET (Z) of the BASE UNIT (C). Slide the MONOCOLUMN down until it is fully seated. Secure the MONOCOLUMN to the MONOCOLUMN BRACKET using two
CAUTION: Be careful not to pinch the WIRE(s) (AA) leading from the MONOCOLUMN BRACKET (Z) when inserting the MONOCOLUMN (T) into the MONOCOL-
UMN BRACKET.
15.Connect the WIRE(s) (AA) leading from the MONOCOLUMN BRACKET (Z) to the corresponding WIRE (U) from the SIDE ACCESS HOLE (Y) of the MONOCOLUMN. Slide the MONOCOLUMN COVER (V) downward to the meet the MAIN SHROUDS (BB). Secure the MONOCOLUMN COVER to the MAIN SHROUDS using four 1/2" PHILLIPS SCREWS (12) and matching FLAT WASHERS (16). Tighten the SCREWS securely. Do not overtighten the SCREWS.
16.Locate the DISPLAY CONSOLE BRACKET (CC) and ACCESSORY TRAY (DD). While holding the WIRE(s)/CON- NECTOR (EE), cut the wire tie securing the CONNECTOR to the MONOCOLUMN (T). Position the DISPLAY CON- SOLE BRACKET and ACCESSORY TRAY near the top of the MONOCOLUMN. Feed the WIRE(s)/CONNECTOR lead- ing from the TOP ACCESS HOLE (FF) of the MONOCOL- UMN through the center hole of the DISPLAY CONSOLE BRACKET and the ACCESSORY TRAY. Secure the DIS- PLAY CONSOLE BRACKET and the ACCESSORY TRAY to the MONOCOLUMN using two 1" PHILLIPS SCREWS (17) and matching FLAT WASHERS (18). Tighten the SCREWS securely.
CAUTION: Be careful not the pinch the WIRE(s)/CON- NECTOR (EE) leading from the MONOCOLUMN (T) when securing the DISPLAY CONSOLE BRACKET (Z) and ACCESSORY TRAY (DD) to the MONOCOLUMN.
NOTE: Be careful not to let the WIRE(s)/CONNECTOR (EE) fall into the MONOCOLUMN (T).
17.Remove the DISPLAY CONSOLE (GG) from its shipping carton. Position the above the ACCESSORY TRAY (DD). Connect the WIRE(s)/CONNECTOR (EE) leading from the DISPLAY CONSOLE BRACKET (Z) to the corresponding JACK(s) located on the back of the DISPLAY CONSOLE. Secure the DISPLAY CONSOLE to the DISPLAY CONSOLE BRACKET using four 1/2" PHILLIPS SCREWS (12). Tighten the SCREWS securely. Do not overtighten the SCREWS.
18.Locate the HANDLEBAR ASSEMBLY (HH). Position the HANDLEBAR ASSEMBLY near the top of the HANDLEBAR TUBE (W). Slide the HANDLEBAR ASSEMBLY fully into the HANDLEBAR TUBE. Secure the HANDLEBAR ASSEMBLY to the HANDLEBAR TUBE using four 5/8" BUTTON HEAD SCREWS (3) and matching FLAT WASHERS (4). Tighten the SCREWS securely.
19.Locate the RIGHT PEDAL (JJ) (marked with an "R") and PEDAL STRAP (KK) (marked with an "R"). With the side of the PEDAL STRAP marked with an “R” facing upward, slide the slotted end of the PEDAL STRAP through the left slot in the PEDAL. Fasten one of the slots onto the TAB located under the left slot of the PEDAL. Bend the PEDAL STRAP upward and slide the remaining end of the PEDAL STRAP through the right slot in the PEDAL and into the STRAP ADJUSTMENT CLIP. The PEDAL STRAP should securely engage the STRAP ADJUSTMENT CLIP.
20.Install the RIGHT PEDAL (JJ) to the USER RIGHT CRANK ARM (LL). Repeat for the LEFT PEDAL (MM) (marked with an "L") and PEDAL STRAP (NN) (marked with an "L").
NOTE: The LEFT PEDAL (MM) has reverse threads.
21.Position the unit in the desired location for use. The unit can be easily moved into place by lifting the rear of the unit and rolling it on the front rollers. Level the unit before use. Refer to the leveling instructions stated in the operations portion of this manual.
7
