Lightolier MDC20 manual Changing the Fade Rate, Operating Instructions

MULTISET PRO® - PRE-WIRED DIMMING CABINET MDC20

Installation and Operation

Changing the Fade Rate

MultiSet Pro® Dimmers can be programmed for 12 different fade rates. Dimmers can be programmed to have a different fade rate on each scene.

The fade rate choices are:

1.5	seconds	1	minute
3	seconds	2	minutes
4.5	seconds	5	minutes
7.5	seconds	15	minutes
15	seconds	30	minutes
30	seconds	60	minutes

Global Fade Rate = One fade rate for all scenes.

Each dimmer’s fade rate affects all scenes. Examples: Dimmer #1 fade rate set 7.5 sec., dimmer #2 set to 15 sec., and dimmer #3 set to 3 sec. When any scene is selected dim- mers #1, 2, and 3, will respond with 7.5, 15, and 3 seconds, respectively for ON, OFF, A, B, C, D, E, F, G, H, I J, K, and L.

To change the Global Fade Rate that affects all scenes:

1.Tap the OFF button on the Master.

2.Press and hold the SET button. After 3 seconds, either a single green LED or a pair of green LEDs indicates the current “global” fade rate. The bottom LED indi- cates the 1.5 second fade rate, the next LED up is 3 seconds, while the top LED is 2 minutes. If the bottom two LEDs are on, it indicates the 5 minutes fade rate, if the next two LEDs up are lit, it indicates 15 minutes, while the top two LEDs indicate the 60 minute fade rate.

Note: When the two LEDs are on, they will not be at the same intensity.

3.While holding the Set button, tap the top of the rocker to sequence the LEDs through the various fade rates until the desired fade rate is selected.

4.Release the SET button.

5.Repeat steps 2 - 4 for each device.

To change the fade rate that will affect only an individual scene:

1.Tap a scene button on the Master to go to a scene.

2.Press and hold the SET button.

3.After 3 seconds, either a single green LED or a pair of green LEDs indicates the scene’s fade rate.

4.While holding the SET button, tap the top rocker until the desired fade rate is reached.

5.Release the SET button.

6.Repeat above for each scene.

2 min

1 min

30 sec

15 sec

7.5sec

4.5sec 3 sec

1.5sec

“Green”

LED Lights

Figure 9

60 min

30 min

15 min

5 min

Figure 10

Step 1

Press and hold Set button for 3 seconds.

Step 2

Tap top of dimmer paddle to increment fade rate.

Step 3

Release Set button.

Operating Instructions

MULTISET PRO® MASTER (CLASSIC SERIES)

•Tap the ON button to elegantly illuminate the entire area to the ON “preset”.

•Press and hold the ON button to brighten lighting level.

•Tap the OFF button to fade lights to OFF.

•Press and hold OFF button to lower lighting level.

•Tap a scene button to access “preset” light levels.

•Two quick taps of any button (including ON and OFF) will fade lighting quickly.

MULTISET PRO® MASTER (ELLIPSE SERIES)

• Press or Tap the ON button to elegantly illuminate the entire area to the ON “preset”.

• Press the RAISE button to brighten lighting level.

Figure 11

All-On
A	B
C	D	Classic Series

Off

Figure 12

ON

• Tap the OFF button to fade lights to OFF.
•	Press LOWER button to lower lighting level.
•	Tap a scene button to access one of the “preset” light levels.

Raise/Lower Button

Built-in IR

Ellipse Series

• Two quick taps of any button (except RAISE or LOWER) will fade lighting quickly.

Receiver OFF

6