| DC Motor Control Board | Check for 120 VAC input to the control board at |
|
| terminals L1 and L2. If not present, check the |
|
| conveyor switch and wiring back to |
|
| then back to power source if necessary. If 120 VAC |
|
| is present at L1 and L2, check the VDC output at |
|
| terminals A+ and |
|
| check the 4 amp and the 1 amp fuses on the |
|
| control board. Also reset and check the mini |
|
| breaker in the armature line to the gearmotor. If |
|
| 120 VAC is present at terminals L1 and L2, but DC |
|
| voltage is not present at A+ and |
|
| amp and 4 amp fuses are good, replace the board. |
|
| If DC voltage is present at A+ and |
|
| does not run, check gear motor as follows. |
| Conveyor Gear Motor | If DC voltage is present at A+ and A- and the motor |
|
| does not run, first check the mini breaker and then |
|
| the conveyor. Refer to the next possible cause. |
|
| Check the leads to the motor for evidence of any |
|
| shorts or opens, and each lead to ground. If the |
|
| motor fails the above tests, replace motor. Remove |
|
| dust cover from the top of the motor and rotate |
|
| motor shaft to determine if there is a locked rotor or |
|
| a locked gearbox (use care so encoder disc is not |
|
| damaged). |
| Conveyor | Check for any mechanical misalignment or |
|
| improper adjustment. Also check for worn bearings. |
|
| The Installation and Operations Manual shows |
|
| proper conveyor belt adjustment. A conveyor belt |
|
| that is over tightened will cause excessive bearing |
|
| wear and sometimes, irregular speed. |
Conveyor speed | Power Supply | Check power supply at the DC control board for the |
varying or intermittent |
| 120 VAC at board terminals L1 and L2. If voltage is |
|
| not present, check main circuit breakers. |
| Tach generator and DC Motor | With the power to the DC motor control board |
| Control Board | turned off, remove the leads from terminals T1 and |
|
| T2.Place the test leads of a digital meter on the |
|
| tach leads, turn power on, and the meter reading |
|
| should be approximately 30 to 35 VDC. This |
|
| reading should be steady within ± 0.2 to 0.3 VDC. If |
|
| this reading is not within + 0.5 VDC, place the test |
|
| meter probes on terminals A+ and |
|
| reading should be approximately 150 to 160 VDC |
|
| and steady within approximately 2 VDC. If the tach. |
|
| voltage is unsteady, and the board output is steady, |
|
| check the coupling for loose set screws or any type |
|
| of damage. If the coupling checks good, the tach. is |
|
| usually bad. If the board voltage output is unsteady |
|
| beyond limits, then the board is probably bad. |
|
| Always check the speed pot. Be sure it is okay |
|
| before changing a board or tach. This test is not |
|
| always 100% accurate as this test is not performed |
|
| at operating speeds. However, this test is the best |
|
| method currently available. Readjustment should |
|
| always be attempted at least once before |
|
| replacement. See procedure for board adjustment |
|
| on page 65. |
| DC Gearmotor | If the DC control board is steady then the problem |
|
| may be the motor or gearbox. Check the brushes in |
|
| the motor for excessive arching and/or unusual |
|
| wear. Check the motor and gearbox from |
|
| instruction located on page 34 under "possible |
|
| cause" listing "Conveyor gear motor". |
42 | Impinger I |
