Lincoln Electric IM762-C manual System Description, Table A.2, Electrode Voltage Sensing

A-5 INSTALLATION A-5

Enable the voltage sense leads as follows:

TABLE A.2

Process	Electrode Voltage	Work Voltage
	Sensing 67 lead *	Sensing 21 lead
GMAW	67 lead required	21 lead optional
GMAW-P	67 lead required	21 lead optional
FCAW	67 lead required	21 lead optional
GTAW	Voltage sense at studs	Voltage sense at studs
GMAW	Voltage sense at studs	Voltage sense at studs
SAW	67 lead required	21 lead optional
CAC	Voltage sense at studs	Voltage sense at studs

*The electrode voltage 67 sense lead is integral to the control cable to the wire feeder.

Electrode Voltage Sensing

Enabling or disabling electrode voltage sensing is automatically configured through software. The 67 electrode sense lead is internal to the cable to the wire feeder and always connected when a wire feeder is present.

CAUTION

Important: The electrode polarity must be config- ured at the feed head for all semi-automatic processes. Failure to do so may result in extreme- ly high welding outputs.

------------------------------------------------------------------------

Work Voltage Sensing

The standard Power Wave 455M’s default to the work stud (work sense lead disabled)

For processes requiring work voltage sensing, con- nect the (21) work voltage sense lead (K940) from the Power Wave work sense lead receptacle to the work piece. Attach the sense lead to the work piece as close to the weld as practical, but not in the return cur- rent path. Enable the work voltage sensing in the Power Wave as follows:

WARNING

• Do not touch electrically live parts or electrodes with your skin or wet clothing.

•Insulate yourself from the work and ground.

•Always wear dry insulating gloves.

-----------------------------------------------------------

1.Turn off power to the power source at the discon- nect switch.

2.Remove the front cover from the power source.

3.The control board is on the left side of

the power source. Locate the 8-position		8
DIP switch and look for switch 8 of the		7
DIP switch.		6
		5
4. Using a pencil or other small object,		4
		3
slide the switch right to the OFF posi-
		2
tion if the work sense lead is NOT con-		1
nected. Conversely, slide the switch to
	O N
the ON position if the work sense lead

is present.

5.Replace the cover and screws. The PC board will “read” the switch at power up, and configure the work voltage sense lead appropriately.

POWER WAVE TO SEMI-AUTOMAT- IC POWER FEED WIRE FEEDER INTERCONNECTIONS

The Power Wave 455M and semi-automatic POWER FEED family communicate via a 5 conductor control cable (K1543). The control cable consists of two power leads, one twisted pair for digital communication, and one lead for voltage sensing. The cables are designed to be connected end to end for ease of extension. The out- put receptacle on the Power Wave 455M is located beneath the spring loaded output cover at the bottom of the case front. The input receptacle on the Power Feed is typically located at the back of the feeder, or on the bottom of the user interface.

For convenience sake, the electrode and control cables can be routed behind the left or right strain reliefs (under the spring loaded output cover), and along the channels formed into the base of the Power Wave, out the back of the channels, and then to the wire feeder.

Due to the flexibility of the platform the configuration may vary. The following is a general description of the sys- tem.

SYSTEM DESCRIPTION

The Power Wave 455M and Power Feed M family of products utilize a digital communication system called ArcLink. Simply put, ArcLink allows large amounts of information to be passed at very high speeds between components (nodes) in the system. The system requires only two wires for communication, and because of its bus-like structure, the components may be connected to the network in any order, thus simplifying the system set- up.

Each "system" must contain only one power source. The number of wire feeders is determined by the type of wire feeder. Refer to the wire feeder instruction manual for details

POWER WAVE 455M