B-5

OPERATION

B-5

 

 

 

FIGURE B.6

Making A Weld

1.See “Process Guidelines” in this section for selec- tion of welding wire and shielding gas and for range of metal thicknesses that can be welded.

2.See the Application chart on the inside of the wire feed compartment door for information on setting the PRO 100 controls. Refer to Table B.1 for alu- minum and stainless wire.

3.Set the Voltage (“V”) and Wire Speed (“olo’”) con- trols to the settings suggested for the welding wire and base metal thickness being used, refer to Applications chart on the inside of the wire drive compartment door.

4.Check that the polarity is correct for the welding wire being used and that the gas supply, if required, is turned on.

5.When using Innershield electrode, remove the gas nozzle and install the gasless nozzle. This will improve visibility of the arc and protect the gas dif- fuser from weld spatter. Refer to the MAINTE- NANCE section for details on nozzle replacement.

FIGURE B.7

GUN CABLE

WORKPIECE

ARC

WORK CLAMP

6.Refer to Figure B.7. Connect work clamp to metal to be welded. Work clamp must make good elec- trical contact to the workpiece. The workpiece must also be grounded as stated in “Arc Welding Safety Precautions” in the beginning of this manu- al.

7.Position gun over joint. End of wire may be lightly touching the work.

8.Lower welding helmet, close gun trigger, and begin welding. Hold the gun so the contact tip to work distance is about 3/8 inch (10 mm).

9.To stop welding, release the gun trigger and then pull the gun away from the work after the arc goes out.

10.When no more welding is to be done, close valve on gas cylinder (if used), momentarily operate gun trigger to release gas pressure, and turn off the PRO 100.

Cleaning Tip And Nozzle

Clean the contact tip and nozzle to avoid arc bridging between the nozzle and contact tip which can result in a shorted nozzle, poor welds and an overheated gun. Hint: Anti-stick spray or gel, available from a welding supply distributor, may reduce buildup and aid in spat- ter removal.

PROCESS GUIDELINES

The PRO 100 as shipped, can be used for welding mild steel using the self shielded, Innershield elec- trode process or it can be used for the GMAW (MIG), single pass, process which requires a supply of shielding gas and the K610-1 MIG Conversion Kit.

The recommended electrode for the self-shielded process is 0.035” (0,9 mm) diameter Lincoln Inner- shield NR-211-MP on 10 Ib (4,5 kg) spools. Requires optional spindle – refer to Accessories section. This electrode can be used for all position welding of 20 gauge through 5/16” (1,0 – 8,0 mm) thick steel [multi- ple passes are required for 1/4” and 5/16” (6,0 and 8,0 mm)].

The recommended gas and electrode for GMAW is welding grade CO2 gas and 0.025” (0 6 mm) diameter Lincoln L-56 mild-steel welding wire [supplied on 12-1/2 Ib (6 kg) spools]. For 14 gauge (2,0 mm) and thinner, CO2 gas is recommended because it gives equal or better performance than a blended gas at a

PRO 100

Page 17 Page 19
Page 18
Image 18
Lincoln Electric PRO 100 manual Process Guidelines, Making a Weld, Cleaning Tip And Nozzle
Page 17 Page 19

PRO 100 specifications

The Lincoln Electric PRO 100 is a compact and versatile multi-process welder designed to meet the needs of both novice and experienced welders. Known for its robust build quality and advanced features, the PRO 100 is engineered for tasks ranging from light fabrication to heavy-duty welding projects.

One of the standout features of the PRO 100 is its multi-process capability. It can seamlessly switch between MIG, Stick, and TIG welding, allowing users to tackle various materials including aluminum, stainless steel, and mild steel with ease. This versatility makes it an essential tool for welding professionals and hobbyists alike, enhancing productivity and efficiency on the job.

The machine is equipped with Lincoln Electric's unique Auto-Set technology, which simplifies the setup process for users. By automatically adjusting the voltage and wire feed speed based on the selected material and thickness, it enables welders to achieve optimal results without extensive experience or technical knowledge. This feature not only saves time but also reduces the likelihood of mistakes, making it ideal for beginners.

Powering the PRO 100 is a reliable inverter-based technology that ensures smooth and consistent arcs. This technology not only enhances performance but also improves energy efficiency, making the machine more cost-effective in the long run. The compact design allows for portability, making it convenient for job sites where space may be limited.

The PRO 100 also boasts several safety features that protect both the user and the machine. It includes an overload protection system that prevents overheating, ensuring the longevity of the welder. Additionally, the welder features a rugged construction that can withstand demanding work environments, further enhancing its durability.

Furthermore, the PRO 100 is designed for user comfort and control. The intuitive interface and large color display provide clear readability of settings and parameters, allowing for quick adjustments. The adjustable wire feed speed and voltage settings give welders the flexibility to customize their welding experience.

In summary, the Lincoln Electric PRO 100 stands out in the crowd of welding machines for its multi-process capabilities, Auto-Set technology, and inverter-based power system. Its combination of portability, durability, and user-friendly features makes it an excellent choice for a wide range of welding applications, whether at home, in the workshop, or on the field. This well-rounded welder can help elevate the quality of the work for both the novice and the seasoned professional.
Top Page Image Contents