Network Setup, Optional Settings, Router IP | Linksys RT31P2

connection. If the connection is down, then the Router will automatically re-establish the connection. To use this option, click the radio button next to Keep Alive. The default Redial Period is 30 seconds.

When you are finished, click the Save Settings button. Then click the Status tab, and click the Connect button to start the connection.

Optional Settings

Some of these settings may be required by your ISP. Verify with your ISP before making any changes.

Host Name and Domain Name. These fields allow you to supply a host and domain name for the Router. Some ISPs require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work.

MTU. The MTU (Maximum Transmission Unit) setting specifies the largest packet size permitted for network transmission. Select Enable and enter the value desired. It is recommended that you leave this value in the 1200 to 1500 range. For most DSL users, it is recommended to use the value 1492. By default, MTU is set at 1500 when disabled.

Broadband Router with 2 Phone Ports

packet: a unit of data sent over a network

Network Setup

The Network Setup section allows you to change the Router’s local network settings.

Router IP

The values for the Router’s Local IP Address and Subnet Mask are shown here. In most cases, keeping the default values will work.

Chapter 5: Configuring the Router

21

The Setup Tab - Basic Setup

Image 27

Linksys RT31P2 manual Network Setup, Optional Settings, Router IP, Packet a unit of data sent over a network

Contents

Broadband Router How to Use this Guide Copyright and TrademarksWord definition Table of Contents Common Problems and Solutions Frequently Asked Questions Appendix a Troubleshooting Front Panel Back Panel 16 Security Tab VPN Passthrough Welcome Introduction What’s in this Guide? Introduction What’s in this Guide? Broadband Router with 2 Phone Ports Networking Basics An Introduction to Local Area NetworksUse of IP Addresses Networking Basics Back Panel Getting to Know the Router Front Panel Proceed to Connecting the Router Broadband Router with 2 Phone Ports Overview Connecting the Router Connect a PC Connection Instructions Setup Configuring the Router Security VoiceApplications & Gaming How to Access the Web-based Utility AdministrationStatus Obtain an IP automatically Setup Tab Basic SetupInternet Setup Internet Connection Type PPPoE Static IP PPPoE RAS for SingTel Pptp Heart Beat Signal Heart Beat Signal Packet a unit of data sent over a network Network SetupOptional Settings Router IP Network Address Server Settings Dhcp Time Setting Setup Tab Ddns TZO.com DynDNS.org MAC Clone Setup Tab MAC Address Clone Advanced Routing Setup Tab Advanced Routing 13 Routing Table Entry List Filter MAC Address Security Tab FilterFilter IP Address Range Filter Port Range 15 Filtered MAC Address Block WAN Requests VPN Passthrough Security Tab VPN Passthrough Port Range Voice TabApplications & Gaming Tab Port Range Forwarding Port Range Forwarding Applications & Gaming Tab Port Triggering Port TriggeringTriggered Range Applications & Gaming Tab UPnP Forwarding UPnP ForwardingForwarded Range Configuring the Router Broadband Router with 2 Phone Ports DMZ Applications & Gaming Tab DMZ Application-based QoS Applications & Gaming Tab QoS Specific Port# fields Port-based QoS Voice QoS Remote Router Access Administration Tab ManagementRouter Password Local Router Access UPnP Backup and Restore Log Administration Tab Log Administration Tab Factory Defaults Administration Tab Firmware UpgradeFirmware the programming code that runs a networking device Line2 Status Status Tab VoiceInformation Line1 Status 31 Status Tab Router Status Tab Router Local Network Status Tab Local Network Common Problems and Solutions Appendix a Troubleshooting Need to set a static IP address on a PC For Windows 98 and Millennium For Windows XP For Windows Want to test my Internet connection For Windows XP Configuring the Router for details Am not able to access the Router’s Web-based Utility Setup Need to set up a server behind my Router TCP Application Start and End Protocol IP Address Enabled Can’t get the Internet game, server, or application to work Broadband Router with 2 Phone Ports For Netscape 4.7 or higher To start over, I need to set the Router to factory defaultMy DSL service’s PPPoE is always disconnecting For Microsoft Internet Explorer 5.0 or higher Broadband Router with 2 Phone Ports Need to use port triggering Can I make calls while I’m browsing the Internet? Frequently Asked QuestionsHow do I make a phone call? Can I make calls if my Internet connection is down? Where is the Router installed on the network? Is IPSec Passthrough supported by the Router?Does the Router support IPX or AppleTalk? How can I block corrupted FTP downloads? Broadband Router with 2 Phone Ports If all else fails in the installation, what can I do? What is DMZ Hosting?Will the Router function in a Macintosh environment? How can I check whether I have static or Dhcp IP addresses? Is the Router cross-platform compatible?How many ports can be simultaneously forwarded? Which modems are compatible with the Router? Windows 98 or Me Instructions Figure B-1 IP Configuration Screen For the Router’s Web-based Utility Windows 2000 or XP Instructions Appendix C Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix C Windows Help Appendix D Glossary Appendix D Glossary Broadband Router with 2 Phone Ports Packet a unit of data sent over a network Broadband Router with 2 Phone Ports Broadband Router with 2 Phone Ports Two Standard Phone Ports, One Power Port Appendix E Specifications Appendix E Specifications Limited Warranty Appendix F Warranty Information Appendix F Warranty Information FCC Statement Appendix G Regulatory Information Appendix G Regulatory Information Appendix H Contact Information Appendix H Contact Information