Manuals / Linksys / Computer Equipment / Network Router

Linksys WRVS4400N manual Advanced Routing, Operating Mode, Dynamic Routing

Models: WRVS4400N

1 134

Download 134 pages 37.56 Kb

Page 43

Wireless-N Gigabit Security Router with VPN

Advanced Routing

Operating Mode

Select the Operating mode in which the Router will function.

Internet Gateway. This is the normal mode of operation. This allows all devices on your LAN to share the same WAN (Internet) IP address. In the Internet Gateway mode, the NAT (Network Address Translation) mechanism is enabled.

Intranet Router. You either need another Router to act as the Internet Gateway, or all PCs on your LAN must be assigned (fixed) Internet IP addresses. In Intranet Router mode, the NAT mechanism is disabled.

Dynamic Routing

The Router's dynamic routing feature can be used to automatically establish a routing table through a database exchange with peer routers (running the same routing protocol). The Router supports RIP (Routing Information Protocol) versions 1 & 2.

RIP (Routing Information Protocol. The Router, using the RIP protocol, calculates the most efficient route for the network’s data packets to travel between the source and the destination based upon the shortest paths.

RIP Send Packet Version. Choose the version of RIP packets you want to send to peers: RIPv1 or RIPv2. This should match the version supported by other Routers on your LAN.

RIP Recv Packet Version. Choose the version of RIP packets you want to receive from peers: RIPv1 or RIPv2. This should match the version supported by other Routers on your LAN.

Chapter 6: Setting Up and Configuring the Router

Figure 6-14: Setup - Advanced Routing

35

Setup Tab

Image 43

Linksys WRVS4400N manual Advanced Routing, Operating Mode, Dynamic Routing

Contents

Wireless-N Gigabit Security Router with VPN Copyright and Trademarks How to Use this GuideWord definition Table of Contents Appendix E Glossary Appendix C Configuring a Gateway-to-Gateway IPSec TunnelAppendix F Specifications Appendix G Warranty InformationExample network List of Figures11 Setup LAN 41 VPN IPsec VPN 71 LAN ARP Table 72 Status Wireless LANWelcome IntroductionWhat’s in this Guide? Wireless-N Gigabit Security Router with VPN An Introduction to LANs Networking and Security BasicsNetworking and Security Basics Use of IP AddressesNetworking and Security Basics Use of IP Addresses Intrusion Prevention System IPS Wireless-N Gigabit Security Router with VPN Planning Your Virtual Private Network VPN Why do I need a VPN?Packet a unit of data sent over a network What is a VPN? VPN Router to VPN Router Computer using the Linksys VPN client software to VPN RouterGetting to Know the Router PowerDiag Back Panels Antennas and Positions Stackable Position and its Antenna SetupOverview Connecting the RouterConnect a PC Connection InstructionsStand Option Placement OptionsWall-Mount Option Mounting DimensionsBasic Setup Setting Up and Configuring the RouterHow to Navigate the Utility How to Access the Web-based UtilitySetup Firewall WirelessQoS AdministrationStatus L2 SwitchIP Versions Setup TabInternet Connection Type Automatic Configuration DhcpStatic IP Pptp PPPoESetup WAN Heart Beat Signal Heart Beat SignalL2TP Setup WAN Optional Settings Optional Settings Required by some ISPsTZO.com DynDNS.orgIPv4 Server Settings DhcpIPv6 MAC Address Clone DMZAdvanced Routing Operating ModeDynamic Routing Static Routing 15 Setup Advanced Routing RoutingTime 16 Setup TimeBasic Wireless Settings Wireless TabBasic Settings Setting Up and Configuring the Router Wireless Tab WPA-Personal also known as WPA-PSK Wireless SecurityWireless Security DisabledWPA2-Personal Mixed WPA2-PersonalWPA2-Enterprise WPA-EnterpriseWEP WPA2-Enterprise MixedConnection Control Wireless Connection ControlWireless Connection Control Wireless Client ListAdvanced Wireless Advanced Wireless SettingsSetting Up and Configuring the Router Wireless Tab Firewall Tab Basic SettingsRestrict WEB Features Source Interface Select LAN, WAN, or ANY interface IP Based ACLNew Rule Edit IP ACL RuleScheduling 34 Firewall Internet Access Policy Internet Access Policy35 Firewall Internet Access Policy Summary 37 Firewall Single Port Forwarding Single Port Forwarding38 Port Range Forwarding Port Range Forwarding39 Port Range Triggering Port Range Triggering40 Firewall Services ServiceRemote Security Group VPN TabIPsec VPN Local Security GroupAuto IKE Key Management43 View VPN Tunnel Log Manual44 IPsec VPN Advanced Settings Advanced Settings Phase 1 and PhaseSetting Up and Configuring the Router VPN Tab VPN Client List Table VPN Client Accounts46 VPN VPN Passthrough VPN PassthroughApplication-based QoS Tab48 Port-based Port-basedLocal Gateway Access Administration TabManagement Log 50 Administration LogPing Test Parameters DiagnosticsTraceroute Test Parameters Save Configuration Config ManagementRestore Configuration Firmware Upgrade Factory DefaultsIPS Tab ConfigurationAbnormally Detection Instant Messenger Peer to PeerAttacker ReportAttacked Category 62 IPS Information InformationVlan Configuration L2 Switch TabRadius Port. Specifies the number of the four LAN ports Port Settings67 L2 Switch Cable Diagnostics Cable DiagnosticsWAN / Gateway Status TabInternet Connection 69 Status LAN 72 Status Wireless LAN Wireless LANSystem Performance L2 Switch Ports74 Status VPN Clients VPN ClientsNeed to set a static IP address on a PC Appendix a TroubleshootingCommon Problems and Solutions For Windows 98 and MillenniumFor Windows XP For WindowsFor Windows 98 and Millennium Wireless-N Gigabit Security Router with VPN Need to set up a server behind my Router Am not able to access the Router’s Web-based Utility SetupTCP Application Start and End Protocol IP Address EnableCan’t get the Internet game, server, or application to work Application Start and End Protocol IP Address EnabledFor Netscape 4.7 or higher To start over, I need to set the Router to factory defaultNeed to upgrade the firmware For Microsoft Internet Explorer 5.0 or higherMy DSL service’s PPPoE is always disconnecting Firmware upgrade failedNeed to use port triggering Does the Router support IPX or AppleTalk? Frequently Asked QuestionsWhere is the Router installed on the network? Is IPSec Passthrough supported by the Router?How can I block corrupted FTP downloads? What is Network Address Translation and what is it used for?Router allows Pptp packets to pass through What is DMZ Hosting?How can I check whether I have static or Dhcp IP addresses? Is the Router cross-platform compatible?How many ports can be simultaneously forwarded? Which modems are compatible with the Router?Figure B-1 VPN Client Accounts Screen Before You BeginInstalling from the CD-ROM Installing the Linksys QuickVPN SoftwareDownloading and Installing from the Internet Figure B-2 QuickVPN Using the Linksys QuickVPN Software102 Figure C-1 Diagram of Gateway-to-Gateway VPN Tunnel Appendix C Configuring a Gateway-to-Gateway IPSec TunnelConfiguring VPN Router Configuring the VPN Settings for the VPN Routers105 Configuring the Key Management Settings Configuring PC 1 and PC Windows 2000 or XP Instructions Windows 98 or Me InstructionsFigure D-3 MAC Address/Physical Address For the Router’s Web-based Utility110 Appendix E Glossary111 112 113 114 115 Model Appendix F SpecificationsManagement Snmp Version Snmp Version 1, 2c 3DES Encryption QuickVPN Tunnels for remote client accessMD5/SHA1 Authentication SecurityAny host IP address on LAN side Queues Network Vlan Support Port-based VlanLimited Warranty Appendix G Warranty InformationFCC Statement Appendix H Regulatory Information121 122 123 124 125 Need to contact Linksys? Appendix I Contact InformationInformation section in this Guide