Initial installation
Explanations of the setting possibilities:
Location | Select the country for | |
of TV set | If UK or IRL is selected for the location of TV set, it is pos- | |
| sible to activate | |
| A dialogue appears, where you can confirm to set the | |
| operating software to the selected location. | |
| If Yes is selected and confirmed with OK, the TV set turns | |
| off and on again automatically. First installation starts | |
| again after activating the operation software. | |
| If | |
| used anymore. Only terrestrial/cable and | |
| are available. |
|
Antenna | Antenna/cable (analogue): analogue stations via | |
selection | cable/antenna | |
| digital terrestrial stations | |
|
| digital stations via cable |
|
| digital stations via satellite |
| digital stations via satellite | |
Encrypted | You can state whether coded stations are to be searched | |
stations | for in the search/update. Select yes then coded stations | |
| are also searched for. However, these stations can only | |
| be received in connection with a CA module and the | |
| appropriate Smart Card. Handling of the CA module is | |
| described on page 35. |
|
If you are using an active antenna, then select yes (5V) | ||
Antenna | for the antenna power supply. | |
The conventional settings will be derived from the selection | ||
Settings | of set location. Only change this if you know other symbol | |
| rates and modulation types or if you have to specify the | |
| network ID for your cable network (information available | |
| from your cable network provider). If you want to run the | |
| station search independently of the channel grid, select | |
| frequency search for the search method. | |
| Select which satellite(s) you receive from a list. For more | |
Satellite | than one satellite, select the type of your changeover | |
system | switch or communal satellite system additionally. | |
| Ask your dealer in this regard. | |
High band | Specify here whether the high band of the selected satellite | |
| is to be searched in addition to the low band. | |
LNC | Normally, you do not need to change the values for high |
frequencies | and low band, unless the LNC (LNB) of your satellite |
Low Band / | system uses a different oscillator frequency (important |
High Band | for the frequency display). |
| After you have made these settings, you should receive |
| the picture and sound of the selected satellites (only with |
| Astra1 and HOTBIRD). |
Search | If you want to run the station search independently of |
method | the channel grid, select frequency search for the search |
| method. |
Symbol rates | The symbol rates are specified by the satellite provider |
| and normally do not need to be changed. |
Favoured | Select the signal source that provides the stations to be on |
signal source | top of your station list (starting with station slot 1). |
Start search | Start the automatic station search with OK. |
| First TV stations, then radio stations are searched for. |
| The stations found in the automatic search are divided |
| into the appropriate station blocks depending on the |
| previously selected antenna cables (signal sources). Sub- |
| sequently the stations can only be |
| blocks. At the beginning of the station list you will find the |
| block with the stations of the preferred signal source. |
| Any mixed sorting of stations from different signal sources |
| is only possible with the favourites list. |
| ➠ For TV sets with |
| tied to “Logical Channel Numbers” – “LCN” and |
| sorted from |
| stored from 800 onwards. Analogue stations are stored |
| from 1001. |
Connecting | Then the connection and sound component wizard |
additional | starts which helps you to log in, set and connect video |
devices | recorders, decoders, a loudspeaker system or a HiFi/AV |
| amplifier to your TV set. DVD players and DVD recorders |
| are already registered at the factory. |
| You can start the connection wizard and the sound |
| components wizard manually later and add new devices. |
| Further information is available from page 40 (Connection |
| wizard) and page 47 (Sound components wizard). |
continued on next page
13 - 
