Magnat Audio MC 1 manual Functions of the MC, Functions of the CD Player, Functions of the Tuner

FUNCTIONS OF THE MC 1

GB

FUNCTIONS OF THE CD PLAYER

Playing a CD

•Open the CD compartment by pressing the EJECT button.

•Insert the CD into the compartment (with the label facing upwards).

•Close the compartment by pressing the EJECT button.

•Press PLAY to listen to the first track on the CD.

SACDDisplay:

Title No. Play time

Pausing a CD

•Press the PLAY(PAUSE) button to pause the CD.

•Press this button again to resume playback of the CD.

Selecting the track directly

•Turn the TONE/SKIP knob clockwise to select a higher track.

•Turn the knob anti-clockwise to select a lower track.

•Press the PRESET buttons on the remote control.

Searching within a track

•Press the right/left search button to search forwards/backwards within a track respectively. Briefly pressing this button activates the search function;

pressing the button again will stop the search function.

•Press the TUNING buttons on the remote control.

Stopping playback from a CD Press one of the STOP buttons.

CD repeat mode

The repeat function can only be activated via the remote control.

Repeating a track:

Start the CD. The REP button repeats the current track. The following appears in the display:

Repeating the entire CD:

Start the CD.

Press the REP button twice.

The following appears in the display:

Repeating from point A to point B: Start the CD.

Press the A-B button at point A, allow the CD to play until it reaches point B and then press the A-B button again.

Stopping the repeat function:

Press the REP button repeatedly until none of the above symbols are illuminated in the display.

FUNCTIONS OF THE TUNER

Selecting the tuner band

•Select TUNER as the audio source using the SOURCE (MC 1) or INPUT button (on the remote control).

•Select AM mono, FM mono or FM stereo using one of the FM/AM buttons.

Automatic station search

•Select TUNER as the audio source and choose the band (see above).

•Use the AUTO TUNE buttons on the front of the MC 1 or the TUNING buttons on the remote control.

Manual station search: Briefly pressing these buttons increases or decreases the tuning frequency by 50 kHz.

Automatic station search: Pressing and holding these buttons searches for the next or previous station on the band.

Direct station selection

This function can only be accessed via the remote control.

•1st Example:

Setting the station to FM 107.10 MHz. Select TUNER and FM.

Press the "--" button on the remote control. Press the numerical buttons in succession to enter 1, 0, 7, 1, 0.

•2nd Example:

Setting the station to FM 91.40 MHz. Select TUNER and FM.

Press the "--" button on the remote control. Press the numerical buttons in succession to enter -- 9, 1, 4, 0.

Station presets

•A total of 80 FM and AM stations can be stored in the memory.

•Select the desired station (FM or AM). Open the memory using the MEMORY button on the front panel or on the remote control.

•Choose the desired station number using the TONE/SKIP button on the front panel or via the numerical buttons on the remote control.

•The station number and MEM flash in the display.

•Press one of the MEMORY buttons again to store the station.

•The station number stops flashing and MEM disappears.

•Repeat this procedure to store other stations.

Selecting the preset stations

•Press the SOURCE button and select TUNER as the audio source.

•Turn the TONE/SKIP knob on the front panel or press one of the PRESET buttons on the remote control to select the desired station number.

The memory slot can also be selected directly by using the numerical buttons.

Display during radio operation

FM stereo:

	Sender eingestellt			Stereoempfang
Bei RDS Empfang			FM stereo
	Sendernummer	FM			Senderfrequenz

FM mono:

	Station
		set
During RDS reception			FM mono

Station number FM Station frequency

16