Magnavox 19ME601B owner manual Initial Setup, Make sure the unit is connected to antenna or cable

These operations are accessible by remote control.

Some may also be accessible by controls on the main unit.

Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoprogram, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.

1 After making all the necessary connections, pressto turn on the unit.

•It may take a few moments to turn on the unit for the first time.

•[Initial Setup] menu appears automatically after the unit is turned on.

2 Use ▲/▼ to select the on-screen language from the choices (English / Español / Français) on the right side of the TV screen, then press OK.

3 Use ▲/▼ to select [Antenna] for TV channels or [Cable] for CATV channels, then press OK.

Initial Setup

Make sure the antenna is connected to ''ANT. IN'' jack.			Antenna
Select your signal source.			Cable
			Skip
Antenna	Or
Cable		ANT.IN
Select	OK OK	BACK Back	MENU Skip

•[Autoprogram] will begin.

Initial Setup

Please wait while the system is scanning for channels. Auto programming may take more than 20 minutes to complete.

0%

Digital channels	0 ch
Analog channels	0 ch

MENU Skip

		English	11
4 Use ◄/► to select the desired location setting, then press			INTRODUCTION
OK.
[Home] is ENERGY STAR® qualified setting.
	Initial Setup

Select “Retail” or “Home” for your location.

										PREPARATION
				Retail			Home
					Select		OK	OK
	• Select [Retail] store, the unit will be set up with									WATCHING
		predefined setting for retail displays. In this setting, the
		power consumption may possibly exceed the limited
		requirement of the ENERGY STAR® qualification.
	• Select [Home], the unit is set to maximize the energy									TV
		efficiency for home setting and it can be adjusted
		through a choice of picture and sound quality according
		to your preference. Use this setting to remove the
										USING
		E-Sticker if visible from the display.						➠ p.23
	• When the initial setup is completed, the lowest									FUNCTIONS
		and [Sound] settings you adjusted will not be
		memorized channel with the confirmation message of
		the location setting will be displayed on the TV screen.
	• You must set [Home] in step 4. Otherwise, [Picture]
		memorized after the unit goes into standby mode.
										CONNECTING
•	If you press or MENU during autoprogram, this setup of TV
Note
• If you are not receiving a signal from your cable service, contact
	the Cable provider.
										DEVICES
	channels will be canceled.
•	The initial autoprogram function can be executed for either
	[Antenna] or [Cable] only once.When you change the
•	connection (Antenna / Cable), set [Autoprogram] again. ➠ p.17
	If there is no signal input from the antenna terminal and no									USEFUL
	operation for several seconds after you turn on the unit, helpful
	hints appears. Follow the instructions listed on the TV screen.
										TIPS
		Initial Setup
		No channel is registered.							Retry
									Later
		Try Autoprogram again?
		Verify that you have a cable connected to the “ANT. IN” jack								INFORMATION
		on the back of the TV, the channel installation process
		searches this connection. If you are using a cable or satellite
		box, please confirm the input which you have connected to the
		box and press “SOURCE” key on the remote control to select
		the appropriate source input.
			Select		OK	OK	MENU	Skip

After an initial setup is completed...

• If you want to scan the channels automatically again.

	[Autoprogram]	➠ p.17
•	You can add the desired cable and analog channels
	unmemorized by autoprogram.
	[Add Channels]	➠ p.18
• If you want to change to another language.
	[Language]	➠ p.23
•	If you want to change the location setting.
	[Location]	➠ p.23