Magnavox CMWD2206 A Preparation for Use, Turn on the Unit for the First Time, To Select a Channel

Preparation for Use

Setup

Turn on the Unit for the First Time

	VCR	Operations described in this manual are
		mainly based on the remote control.
1	Turn on the TV and set it to channel 3.
	• If channel 3 has been already occupied for broadcasting,
	see “RF Output Channel” section on page 6.
2	Select your language when turning this unit on for the first time.
	Then press [B] to go to next step.		LANGUAGE SELECT
	STANDBY-ON		B ENGLISH	[ON]
			FRANCAIS
		or	ESPAÑOL
3	Press [B] to start Auto Set Up.			CH 01

AUTO SET UP

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

YES NO

Yes Press [MENU] to exit.

• Refer to “Hint for Cable Box or Satellite Box” section on page 6.

No Please wait for a few minutes. After scanning...

•The tuner stops on the lowest memorized channel.

•You can select only the channels memorized in this unit by using [SKIP/CH. G///K, H/L] (or [CHANNEL K//L]).

•If “AUTO SET UP” appears on the TV screen again, check the cable con- nections. Then, press [B] once again.

Hint

•Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.

To Select a Channel

You can select a channel by using the number buttons or [SKIP/CH. G/K, H/L]

Notes for using the number buttons:

•When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number.

(for example: 117, press [1], [1], [7])

•You must precede single-digit channel numbers with a zero. (for example: 02, 03, 04 and so on)

To Add or Delete Channels

VCR

1 Press [MENU] to select “CHANNEL SET UP”.	TIMER PROGRAMMING
	- M E N U -
Then press [B] to go to next step.	AUTO REPEAT [OFF]
MENU	B CHANNEL SET UP
	CLOCK SET
	LANGUAGE SELECT

or

To Preset the Channel Again

1) Press [MENU] until the main menu appears.

2) Select “CHANNEL SET UP” by using [K/L], then press [B]

3) Select “AUTO SET UP” by using [K/L], then press [B]. After scan- ning, the tuner stops on the lowest memorized channel.

To Change the On-Screen Language

1) Press [MENU] until the main menu appears.

2) Select “LANGUAGE SELECT” by using [K/L], then press [B]

3) Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by using [K/ L] then press [CLEAR/C.RESET]

Hint

•If you accidentally select Spanish or French and need English: Press [MENU] and choose SELEC. IDIOMA or SELECTION LANGUE. Press [B] and select ENGLISH. Finally, press [CLEAR/C.RESET].

•To add or delete channels in this unit, [SKIP/CH. G/K, H/L] button works on the channel number memorized in this unit, [K/L] works on all.

Clock Setup

VCR

1	Press [MENU] and select “CLOCK SET”.	- M E N U -
	Then press [B] to go to next step.	TIMER PROGRAMMING
		AUTO REPEAT [OFF]
		CHANNEL SET UP
	MENU	B CLOCK SET
		LANGUAGE SELECT

or

•If the clock is not set, the CLOCK SET screen appears when you press [MENU]. In this case, go to step 2.

2	Select the current month.	MONTH DAY		YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/ – –	– – – –
		HOUR MINUTE		AM/PM
	or	– –	: – –	– –
3	Select the current day.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY		YEAR
		1 0	/ 0 5	– – – –
		HOUR MINUTE		AM/PM
	or	– –	: – –	– –
4	Select the current year.	MONTH DAY		YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/ 0 5	2 0 0 9
		HOUR MINUTE		AM/PM
	or	– –	: – –	– –
5	Select the current hour.		CLOCK SET
	Then press [B] to go to next step.	MONTH DAY		YEAR
		1 0	/ 0 5 MON	2 0 0 9
	or	HOUR MINUTE		AM/PM
		0 5	: – –	– –

•If the clock is not set, the “CLOCK SET” screen appears when you press [MENU]. In this case, press [MENU] again.

2	Select “MANUAL SET UP”.			CHANNEL SET UP
	Then press [B] to go to next step.			AUTO SET UP
				B MANUAL SET UP
		or
3	Select the channel to be added or deleted.			MANUAL SET UP
				CHANNEL 30	(CATV)
	or	or		ADD
			or
4	Select “ADD” or “DELETE”.			MANUAL SET UP
				CHANNEL 30	(CATV)
		or		DELETE
5	To exit the menu	C. RESET
		CLEAR/

6	Select the current minute.	MONTH DAY		YEAR
			CLOCK SET
	Then press [B] to go to next step.	1 0	/ 0 5 MON	2 0 0 9
		HOUR MINUTE		AM/PM
	or	0 5	: 4 0	– –
7	Select “AM” or “PM”.		CLOCK SET
		MONTH DAY		YEAR
		1 0	/ 0 5 MON	2 0 0 9
	or	HOUR MINUTE		AM/PM
		0 5	: 4 0	P M AM
				B PM
8	To exit the CLOCK SET screen

Hint

•To go back one step, press [s] (during steps 2 to 7).

•Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds.

8 EN