|
|
|
|
|
|
|
| UVSRC | |||||
3a |
| 3c |
|
|
|
|
| 3d |
|
|
|
|
|
|
| Clearance to Combustible Mantel | Clearance to Combustible Mantel | ||||||||||
|
| Projections without Canopy |
| Projections with Canopy |
|
| |||||||
|
| 42" |
|
|
|
|
|
|
|
|
|
|
|
|
| OpeningFireplaceofopTfromClearance*(“) | 24 |
|
|
|
| OpeningFireplaceofopTfromClearance*(“) | 22 |
|
|
|
|
| Min. | 22 |
|
|
|
| 20 |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 5" Min. |
| 20 |
|
|
|
|
| 18 |
|
|
|
|
|
| 18 |
|
|
|
|
| 16 |
|
|
|
| |
Combustible |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| ||
Perpendicular Wall |
| 16 |
|
|
|
|
| 14 |
|
|
|
| |
3b | 10" |
| 14 |
|
|
|
|
| 12 |
|
|
|
|
|
| 12 |
|
|
|
|
| 10 |
|
|
|
| |
Clearances |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| 10 |
|
|
|
|
|
|
|
|
|
| |
without Canopy |
|
|
|
|
|
|
| 8 |
|
|
|
| |
| 6" |
| 8 |
|
|
|
|
| 6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 24" |
| 2 | 4 | 6 | 8 | 10 |
| 2 | 4 | 6 | 8 | 10 |
Noncombustible |
|
| Mantel (Combustible) |
|
| Mantel (Combustible) | |||||||
|
|
|
| Projections (“) |
| ||||||||
Material | 16" |
| Projections (“) |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| |||||
| Min. |
|
|
|
|
|
| *Combustible projections above | |||||
| 9¹⁄₂" |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
| the fireplace must be within the | ||||||
| Min. |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
| area described by the dashed line. | ||||||
|
|
|
|
|
|
|
| ||||||
Fireplace |
|
|
|
|
|
|
|
|
|
|
|
|
|
Opening |
| FP604a |
|
|
|
|
|
|
|
|
|
| T225 |
|
|
|
|
|
|
|
|
|
|
|
| ||
Fig. 3 Clearances to combustibles. |
|
|
|
|
|
|
|
|
|
|
|
| |
opening and a 10” projection at 24” above the opening. (Fig. 3b and 3c)
To install the optional canopy, you will need a phillips screwdriver. The canopy has four holes along the top edge. The middle two holes are smaller than the outer two holes. Remove the four (4) screws in the upper channel (to front edge) of the firebox. The canopy will fit tightly in the top front edge of the fireplace opening. Attach the canopy with the four (4) sheet metal screws previously removed from the upper channel.
4.Floor Clearances: No clearance is required if the appliance is installed per these instructions.
Installing the Firebox
This list of specific instructions will help you make certain that every installation operation is done cor- rectly. Complete the installation steps in the sequence shown.
LOCAL BUILDING CODES SHOULD BE CONSULTED IN ALL CASES AS TO THE PARTICULAR REQUIRE- MENTS CONCERNING THE INSTALLATION OF FACTORY BUILT FIREPLACES.
Select the location for the fireplace by taking into consideration the factors previously outlined in the Choosing the Location section of the manual.
Step 1: Framing the Firebox
The width of the framed opening must be 39¹⁄₄" for UVSRC36A or 45¹⁄₄" for UVSRC42A. (Fig. 4)
The entire fireplace can be elevated above the floor to achieve a raised hearth effect. This can be done by adding a small platform to achieve the desired height. NOTE: See
Step 2: Install the Firebox
Install the firebox into the framed opening by setting it directly in front of the opening and sliding it into the proper position.
Step 3: Level the Firebox
Check the level of the firebox on the top edge of the fireplace face. Shim if necessary.
Step 4: Secure the Firebox
Secure the fireplace to the framing. The nailing flanges on the firebox will make securing the firebox to the frame quick and easy. Use appropriate size nails or screws to secure the firebox.
Step 5: Gas Piping and Connection
The gas piping must be installed in accordance with local codes or, in the absence of local codes, in accor- dance with the National Fuel Gas Code, ANSI Z223.1/ NFPA 54, latest edition.
20007435 | 5 |
