ENGLISH |
Introduction Connections Playback Function Setup Others
Function Setup
Network Connection
Connection Test
After you made IP address/DNS settings or when a LAN cable is connected, always perform the connection test to check if the connection is correctly made.
1)Press [SETUP] in stop mode.
2)Use [Y / Z] to select 
, then press [ENTER].
3)Use [Y / Z] to select 
, then press [ENTER].
4)Use [U / V] to select “Network Connection”, then press [ENTER].
5)Use [U / V] to select “Connection Test”, then press [ENTER].
Connection test will start automatically and the test result will appear right after the connection test finishes.
• “Testing...” | : The test is in progress. |
• “Pass” | : Connection test is successfully completed. |
• “Fail” | : Connection test failed. Check the connection settings. |
Press [ENTER] to go to the list of network status confirmation screen.
Connection Test
IP Address | ∗∗∗ | . | ∗∗∗ | . | ∗∗∗ | . | ∗∗∗ |
Subnet Mask | ∗∗∗ | . | ∗∗∗ | . | ∗∗∗ | . | ∗∗∗ |
Default Gateway | ∗∗∗ | . ∗∗∗ | . ∗∗∗ | . ∗∗∗ | |||
Primary DNS | ∗∗∗ | . ∗∗∗ | . ∗∗∗ | . ∗∗∗ | |||
Secondary DNS | ∗∗∗ | . ∗∗∗ | . ∗∗∗ | . ∗∗∗ | |||
then press ‘ENTER’.
6) Press [ENTER] to go back to the previous screen or press [SETUP] to exit.
Note
•If the connection test passes, you can enjoy the
•If the connection test fails, you may need to change the MAC address settings of your router. You can check the MAC address of this unit at the bottom of the “Enable(Custom)” screen.
Enable(Easy)
Network settings are set to the following settings initially. (In most cases, you can connect to the Internet without making any changes to the default settings.)
- IP Address Setting | Auto(DHCP) |
- DNS Setting | Auto(DHCP) |
- Proxy Setting | Do Not Use |
- Connection Speed | Auto |
- | Allow |
Function Setup
If you want to set the network settings back to the default settings as above (except
1)Follow steps 1) to 4) in “Connection Test” on this page.
2)Use [U / V] to select “Enable(Easy)”, then press [ENTER].
•The unit will start the connection test automatically and the test result will appear right after the test finishes.
•After the connection test finishes, press [ENTER] to go to network status confirmation screen.
3)Press [ENTER] to activate the network settings and set the network connection automatically. Press [SETUP] to exit.
Note
•The setting of
Enable(Custom)
If you need to set specific settings manually in accordance with your network environment, select “Enable(Custom)” to set each setting as necessary.
IP Address Setting
1)Follow steps 1) to 4) in “Connection Test” on this page.
2)Use [U / V] to select “Enable(Custom)”, then press [ENTER].
3)Use [U / V] to select “IP Address Setting”.
4)Press [ENTER] repeatedly to select the desired setting.
“Auto(DHCP)” : If your router has DHCP server function, select “Auto(DHCP)”.
“Manual” : If your router does not have DHCP server function, select “Manual”.
If you select “Manual”, follow the following instruction to set the IP address.
Use [U / V] to select “IP Address”, then press [ENTER].
•IP address setting screen will appear. Enter IP address, subnet mask and default gateway with [U / V / Y / Z] and [the Number buttons].
IP Address Setting
IP Address
∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗
Subnet Mask
∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗
Default Gateway
∗∗∗ . ∗∗∗ . ∗∗∗ . ∗∗∗
then press ‘ENTER’.
•Enter the IP address number after checking the specifications of your router.
•If the IP address number is unknown, check the IP address number of other devices.
(e.g. PC connected via LAN cable) and assign a different number from those of other devices.
After you enter all correctly, press [ENTER].
• Confirmation message will appear.
Remote control operation | : Displaying the menu | : Move the cursor | : Confirm the setting | : Return to previous menu | |
buttons | Cancel the menu | (Up/Down/Left/Right) | |||
|
|
39
ENGLISH
