ENGLISH | OTHER FUNCTIONS | |
MULTI ROOM SELECTOR | ||
| ||
| The Multi Room Selector is a function which allows you to listen to the | |
| same or a different source in a room other than the room in which the | |
| ||
| remote control signal receiver available from your Marantz dealer are | |
| necessary. The operations possible with the multi room function are | |
| explained briefly below. For details, refer to the instruction manual | |
| supplied with the multi room remote control unit and receiver. |
MULTI ROOM SELECTOR OPERATION
1.Press the MULTI button !9. The unit enters multi room mode and the display indicates “SELCT SOURCE” and flashes the “MULTI” indicator for approx. 10 seconds. In this time, you can select the input source by turning the INPUT SELECTOR knob !5.
2.Then, the display indicates “MULTI VOL” “VOLUME xx dB” for approx. 5 seconds. During this time, you can set the volume level for the multi room operation. This will only set the volume in the second room.
MULTI ROOM SELECTOR OPERATION (USING THE MULTI ROOM REMOTE CONTROL UNIT)
1.Press the M.R. on button on page of Input mode, the POWER ON button, or select the desired source on multi room remote control unit from the second room. Any of these operations will put the
2.Press the VOLUME + or VOLUME – button on the multi room remote control unit to set the desired sound volume.
3.In multi room mode, the multi room remote control unit can be used in the multi room to operate the following functions.
You can select a tuner preset channel and tuning up or down, and direct frequency selection. And you can control the CD player LD player, DVD player and other source connected to the
Caution:
•Multi room mode can only be selected when the
•If the main room is active (not standby mode), you cannot select a radio band except the band of the main room. For example; if the FM band is selected in the main room, you cannot select the AM band in the multi room.
•The operating procedure for this is the same as the
•If you operate from second room,
M U L T I R O O M S E T U P
V I D E O |
| : | D V D |
A U D I O |
| : | D V D |
V O L U M E L E V E L | : | – 7 5 d B | |
|
| : V A R I A B L E | |
S L E E P T I M E R | : | 9 0 m i n | |
– – – M A I N – R OO M S T A T U S – – – | |||
V I D E O | : | L D |
|
A U D I O | : | L D |
|
DIALOGUE NORMALIZATION MESSAGE
Dialogue Normalization (Dial Norm) is a feature of Dolby Digital. When playing back software which has been encoded in Dolby Digital, sometimes you may see a brief message in the front panel display which will read “Dial Norm X dB” (X being a numeric value). Dialogue Normalization serves to let you know if the source material has been recorded at a higher or lower level than usual. For example, if you see the following message: “Dial Norm + 4 dB” in the front panel display, to keep the overall output level constant just turn down the volume control by 4 dB. In other words, the source material that you are listening to has been recorded 4 dB louder than usual.
If you do not see a message or see “Dial Norm 0 dB” in the front panel display, then no adjustment of the volume control is necessary.
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the TV IN jack to control the power (ON/OFF) to the
AUTO POWER ON
1.Be sure TV auto mode is on. (Refer page 18 : System Setup 1/2 )
2.Connect your TV TUNER (etc) to the TV IN terminal. Be sure to connect the video input.
3.Turn OFF the power to the TV TUNER and the
4.Turn ON the TV TUNER and tune in a receivable station.
5.When the station is received, the
AUTO POWER OFF
1.In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.
2.The power to the
Note:
•AUTO POWER OFF is canceled if the INPUT SELECTOR knob !5is set to a source other than TV. The function reactivates when TV is selected again.
Caution:
•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON. To set this function ON/OFF, refer to the SETUP MENU.
SETTING THE SLEEP TIMER (ONLY REMOTE
CONTROL UNIT)
Set the sleep timer while the power is turned on.
1.Turn the power ON and press the Sleep button on page of Control mode.
“SLEEP” blinks on the display.
2.Press the Sleep button the number of times to set the desired sleep time.
Each press of the Sleep button changes the display in the following order:
10 20 30 40 50
OFF 90 80 70 60
“SLEEP” stops blinking and lights steadily.
*While the sleep timer is activated, the remaining time can be displayed for approx. 2 seconds by pressing the Sleep button.
*To cancel the sleep timer, press the Sleep button and then press the Clear button.
This operating procedure is same as the Multi room operations from second room.
22