ENGLISH

ADVANCED CONNECTING

 

 

R L R L R L

 

R L R L R L

R L R L R L

CONNECTING THE REMOTE CONTROL JACKS

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

COMPONENT

 

 

 

 

 

 

 

1

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VIDEO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MONITOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OUT 2

 

 

 

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

INPUT 1

DVD

VCR IN

VCR OUT DSS/VCR2 MONITOR OUT

2 Y

CB/PB

CR/PR

 

Y

CB/PB

CR/PR

Y

CB/PB CR/PR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

4

 

COAX

IN

 

 

 

IN

OUT

IN

 

IN

OUT

IN

OUT

 

1

2

3

OPT

OUT

FLASHER

DC

DVD

VCR1

DSS/VCR2

CD

TAPE

CDR/MD

 

 

DIGITAL IN

 

DIGITAL OUT

RC-5

IN

TRIGER

 

 

 

 

AUDIO

 

 

 

 

 

 

 

 

 

 

 

L

 

R

L

R

 

L

R

 

L

 

 

 

 

 

 

 

2

RC OUT

OPTION

CENTER

L

R

FRONT SURR. SURR. SUB BACK WOOFER

 

 

 

VIDEO

 

 

 

FM (75)

GND

AM

S-VIDEO

 

 

 

 

 

 

 

ANTENNA

 

 

 

 

 

 

 

 

 

TV

DVD

VCR IN

L

SL

C

SBL

 

 

 

L

 

 

 

 

 

 

R

 

 

 

 

 

 

R

SR

SW

SBR MULTI.

 

 

IN

(AUX2)

7.1CH INPUT

OUT

TV

DVD

VC

CENTER

L

R

FRONT SURR. SURR. SUB BACK WOOFER

T B

FRONT A

SURROUND BACK

SURROUND

CENTER

AC OUTLET

B.CENTER.

 

SPEAKER C/

 

SPEAKER

230V 50/60Hz

BACK : 6-8 OHMS

MULTI SPEAKER

 

SYSTEMS

SWITCHED

: 8 OHMS

 

 

 

 

0.65A 150W

1

DVD Audio player

or

Super Audio CD Multi

channel player

 

RS-232C

SPEAKER C

 

 

 

 

OFF ON

 

 

L

SL

C

SBL

 

 

 

 

 

 

R

L

R

SR

SW

SBR

 

FRONT B

FRONT A OR B,CENTER

 

 

 

 

PRE OUT

SURR,SURR BACK:MINI

FRONT A AND B:MINIMU

 

L R L R L R

Power

Amplifer

Subwoofer

REMOTE

CD recorder

REMOTE

MD deck

REMOTE

CD player

CONTROL

 

CONTROL

 

CONTROL

 

IN

 

IN

 

IN

 

OUT

 

OUT

 

OUT

 

 

EXTERNAL INTERNAL

 

EXTERNAL INTERNAL

 

EXTERNAL INTERNAL

Front

Center

Front

Left

Right

 

Surround

Surround

Left

 

Right

Surround

Surround

Back Left

Back Right

q

You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit.

w

Whenever external infrared sensors or similar devices are connected to RC-5 IN of the SR4001/ SR5001, be sure to always disable operation of

CONNECTING MULTI CHANNEL AUDIO SOURCE

The 7.1CH INPUT jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD audio player or external decoder.

If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page 29.

CONNECTING AN EXTERNAL POWER AMPLIFIER

The PREOUT jacks are for connecting external power amplifiers.

Be sure to connect each speaker to the corresponding external power amplifier.

The signal transmitted from the remote control is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote signal only to the unit. Also, if a Marantz power amplifi er (some models excluded) is connected to one of these terminals, the power amplifier’s, power switch is synchronized with this unit’s power switch.

Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature.

the infrared sensor on the main unit by using the following procedure.

1. Hold down the 7.1CH INPUT (SR4001) / MULTI (SR5001) button and MENU button on the front panel at the same time for five seconds.

2. The setting “IR=ENABLE” is shown on the FL DISPLAY.

3. Press the 1or 2cursor button to change this to “IR=DISABLE”.

4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled.

Note:

Be sure to set to “IR=ENABLE” when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands.

5. To restore the original setting, perform steps 1 to 4 to set to “IR=ENABLE”.

20