Marantz SR4001 SORTING PRESET STATIONS, NAME INPUT OF THE PRESET STATION, ←DOWN, A → B → C ... Z → 1 → 2 → 3 ..... 0 →

ENGLISH	CLEARING STORED PRESET STATIONS
ENGLISH	2. 3.	1	2	3
	You can remove preset stations from the memory
	using the following procedure.
					LIP SYNC/
		AUTO		dts	INPUT
	2.	CS	EX/ES	VIRTUAL T.MODE
	2.	7	8	9
		4	5	6
		M-CH ST	STEREO	NIGHT	P.SCAN
			7.1CH IN	A/D	HT-EQ
		CL	0	+10	MEMO
	3.	CH/ CAT	SPKR A/B	MUTE	VOLUME
			SPKR A/B	MUTE
			MULTI/ CAT M-SPKR
		INFO			MENU

1. Recall the preset number to be cleared with the method described in “Recalling” a preset station.

2. Press the MEMO button on the front panel or press the MEMO button on the remote.

3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote.

4. “xx CLEAR” appears on the display to indicate that the specified preset number has been cleared.

Note:

To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds.

SORTING PRESET STATIONS

AV SURROUND RECEIVER SR5001

If you have stations memorized, and there is a gap in the sequential order:

I.e. the stations are stored as follows

1)87.1 MHz

2)93.1 MHz

3)94.7 MHz

10)105.9 MHz

(notice there is no stations programmed for pre sets for 4-9), you can have pre set 10 become pre set 5: To sort the numbers, press and hold the MEMO and the 4cursor buttons.

“PRESET SORT” will appear on the display and sorting will be done.

NAME INPUT OF THE PRESET STATION.

This function allows the name of each preset channel to be entered using alphanumeric characters. Before name inputting, you need to store preset stations with the preset memory operation.

4. 5. 2. 5. 6.

AV SURROUND RECEIVER SR5001

2. 5. 6.	7	8	9
		7.1CH IN	A/D	HT-EQ
	CL	0	+10	MEMO
	CH/ CAT SPKR A/B		MUTE	VOLUME
		MULTI/ CAT	M-SPKR
	INFO			MENU
		ENTER
	T.TONE
	/SET UP			EXIT
	REC	T.DISP	PTY	F.DIRECT
5.	- PRESET +		- TUNING +
5.	DISC+	ANGLE	SUB TITLE	AUDIO
4.	CH-SEL V-OFF		ATT.
4.		BASS	TREBLE
	TV	DVD	VCR	DSS

1. Recall the preset number to be inputted name with the method described in “Recalling” a preset station.

2. Press the MEMO button on the front panel or press the MEMO button on the remote for more than 3 seconds.

3. The left most column of the station name indicator ﬂashes, indicating the character entry ready status.

4. When you press the 3 or 4 cursor buttons on the front panel or the 5 / 6 buttons on the remote, alphabetic and numeric characters will be displayed in the following order:

A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +

→/ → (Blank) → A UP →

←DOWN

5. After selecting the ﬁrst character to be entered, press the MEMO or ENTER buttons, press the MEMO button on the remote.

The entry in this column is ﬁxed and the next column starts to ﬂash. Fill the next column the same way.

To move back and forth between the characters, press the 1/ 2cursor buttons or press Sor Tbuttons on the remote.

Note:

Unused columns should be ﬁlled by entering blanks.

6. To save the name, press the MEMO button on the front panel or remote for more than 2 seconds.

Ten keypad	Press, press again, press again, etc.
1	A → B → C → 1 → A
2	D → E → F → 2 → D
3	G → H → I → 3 → G
4	J → K → L → 4 → J
5	M → N → O → 5 → M
6	P → Q → R → 6 → P
7	S → T → U → 7 → S
8	V → W → X → 8 → V
9	Y → Z → space → 9 → Y
0	– → + → / → 0