ENGLISH
FUNCTION AND OPERATION
REMOTE CONTROL CODE SETTING
The remote control unit contains 3 sets of remote control codes, and it can be used to control up to 3 receivers in one location. To control a second or third receiver, select the remote control code as explained below. The selected receiver can be operated from the remote control.
•When the unit is shipped from the factory, the main unit and remote control are set to RECEIVER1.
1. RECEIVER2
CONNECTIONS
CONNECTING SPEAKERS
System 2
Right Left
AMP
To set the remote control to RECEIVER2, hold down both the AMP button and 2 number button on the remote control for at least five seconds.
RECEIVER3
To set the remote control to RECEIVER3, hold down both the AMP button and 3 number button on the remote control for at least five seconds.
INFO
1, 2, 3
GND
PHONO
IN
L
R
ANTENNA |
|
|
|
|
|
|
|
|
|
| AC OUTLETS | ||
|
|
|
|
|
|
|
|
|
|
|
| 120V | 60Hz |
|
|
|
|
|
|
|
|
|
| UNSWITCHED |
| AC IN | |
|
|
|
|
| VIDEO |
|
| REMOTE | 1.25A 150W |
|
| ||
| AM |
|
|
|
|
| CONTROL |
|
| ||||
|
|
|
|
|
|
|
| IN |
|
|
|
| |
|
|
| AUX | DSS | DVD |
| VCR | MONITOR |
|
|
|
| |
|
|
| IN | IN | IN | IN | OUT | OUT |
|
|
|
|
|
| GND |
|
|
|
|
|
|
| FLASHER |
|
|
| |
|
|
|
|
|
|
|
| IN | SWITCHED |
|
| ||
|
|
|
|
|
|
|
|
|
| 1.25A 150W |
|
| |
|
|
|
|
|
|
|
|
| OUT |
|
|
|
|
| FM (75 | ) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| SYSTEM 1 : MINIMUM 8 OHMS | |||
|
|
|
|
|
|
|
|
|
| SYSTEM 2 : MINIMUM 8 OHMS | |||
|
|
|
|
|
|
|
|
|
| R | SYSTEM | L |
|
|
|
|
|
|
|
|
|
|
|
| 2 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MODEL NO. SR4021 |
|
| AUDIO |
|
|
|
|
|
|
|
|
|
| |
IN | IN OUT | IN OUT | IN | IN | IN | IN | OUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| R | SYSTEM | L |
|
CD | RECORDER 1 | RECORDER 2 | AUX | DSS | DVD |
| VCR | PRE | MAIN | 1 |
| ||
| (TAPE) |
|
|
|
|
| OUT | IN | SPEAKER SYSTEMS |
|
2. Also set the main unit's remote control setting to the same setting as the remote control. To change main unit's remote control setting, hold down both the AMP and INFO buttons on the remote control; the remote control setting (“RECEIVER 1”, “RECEIVER 2” or “RECEIVER 3”) will be displayed in the display
CONNECTING SPEAKER WIRE |
| Right | Left |
|
| System 1 |
window on the main unit and main unit setting will be changed same setting as remote control.
Notes
•To set the remote control back to RECEIVER1, hold down both the AMP button and 1 number button on the remote control for at least five seconds.
•If the batteries in the remote control are replaced while the remote control is set to RECEIVER2 or RECEIVER3, the setting will revert to RECEIVER1.
1.2.
3/8inch
(10 mm)
3. 4.5.
1. Strip away approx. 3/8inch (10 mm) of wire insulation.
2. Twist the bared wire ends tight, to prevent short circuits.
3. Loosen the knob by turning it counterclockwise.
4. Insert the bare part of the wire into the hole in side of each terminal.
5. Tighten the knob by turning it clockwise to secure the wire.
Caution:
•Be sure to use speakers with the specified impedance as shown on the rear panel of this unit.
•To prevent damage to circuitry, do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit.
•Do not touch the speaker terminals when the power is on. It may cause you to receive an electric shocks.
•Do not connect more than one speaker cable to one speaker terminal. Doing so may damage this unit.
Note:
Be sure to connect the positive and negative cables for the speaker properly. If they are
8