REAR PANEL
,AC IN
Connect to supplied an AC power cord, and connect to an AC power outlet.
ENGLISH
1 
2
ANTENNA
AM
AUX DSS
ININ
GND
GND | FM (75 ) |
3 |
| 4 |
| 5 |
| 6 | |
|
|
|
|
|
|
|
|
VIDEO |
|
| REMOTE | |
|
| CONTROL | ||
DVD |
| VCR | MONITOR | IN |
IN | IN | OUT | OUT |
|
|
|
|
| FLASHER |
|
|
|
| IN |
|
|
|
| OUT |
7
AC OUTLETS
120V 60Hz
UNSWITCHED
1.25A 150W
SWITCHED 1.25A 150W
8
AC IN
SR4021 has to be powered by 120V AC only.
.Speaker terminals
Connect your speaker system(s) to these terminals. There are two sets of terminals, so you can connect either 1 and/or 2 speaker systems.
⁄0 MAIN IN jacks
Use these jacks to connect an extension pre amplifier or graphic equalizer.
When a graphic equalizer is to be connected,
SYSTEM 1 : MINIMUM 8 OHMS
SYSTEM 2 : MINIMUM 8 OHMS
R | SYSTEM | L |
| 2 |
|
connect its output jacks with the MAIN IN jacks on
|
|
|
|
| AUDIO |
| |
PHONO | IN | IN | OUT | IN | OUT | IN | IN |
IN |
|
|
|
|
|
|
|
L |
|
|
|
|
|
|
|
R |
|
|
|
|
|
|
|
| CD | RECORDER 1 | RECORDER 2 | AUX | DSS | ||
|
|
|
| (TAPE) |
|
| |
12
MODEL NO. SR4021
IN | IN | OUT |
|
|
|
| R | SYSTEM | L |
DVD | VCR | PRE | MAIN | 1 | ||
|
| OUT | IN | SPEAKER SYSTEMS | ||
|
|
|
|
|
|
11 |
| 10 |
| 9 | |
this unit.
When not used, leave these jacks connected with the supplied connecting pins.
⁄1 PRE OUT jacks
Use these jacks to connect an extension power amplifier or graphic equalizer.
When a graphic equalizer is to be connected, connect its input jacks with the PRE OUT jacks on this unit.
zGND (ground) terminal
Connect the grounding wire from the analog turntable to this terminal.
xAntenna terminals
FM antenna terminal
For connecting the supplied FM antenna or for connecting an external FM antenna with a coaxial cable, or for connecting a cable network.
AM antenna and ground terminal
For connecting the supplied AM loop antenna. Use the terminals marked “AM” and “GND”.
The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna to the best reception.
cVIDEO IN/OUT
(AUX, DSS, DVD, VCR)
bREMOTE CONTROL IN/OUT
terminals
Connect to a Marantz component equipped with remote control
nFLASHER IN (Flasher input
terminal)
This terminal is to control the unit from another zone.
Connect the control signal from a Keypad, etc.
mAC OUTLET
Connect the AC power cord of component such as a DVD or CD player to this outlet.
The marked SWITCHED provides power only when the SR4021 is turned on and is useful for components which you use every time you play your system.
Caution:
When not used, leave these jacks connected with the supplied connecting pins.
⁄2 AUDIO IN/OUT
(PHONO, CD, RECORDER 1, RECORDER 2)
These are the analog audio inputs and outputs. There are 8 audio inputs (4 of which are linked to video inputs) and 3 audio outputs (1 of which is linked to video output). The audio jacks are nominally labeled for recorder1 (CD recorder) recorder2 (cassette tape deck), compact disc players, DVD players and etc....
The audio inputs and outputs require
These are the video inputs and output. There are 4 video inputs and 1 video output. Connect VCR, DVD players, and other video components to the video inputs.
The 1 video output can be used to be connected to video tape recorder for making recording.
vMONITOR output jack
Connect to the TV’s video input (VIDEO IN) jack.
•In order to avoid potential
•The capacity of this AC outlet is 150W. Do not connect devices that consume electricity more than the capacity of this AC outlet. If the total power consumption of the connected devices exceeds the capacity, the protection circuit shuts down the power supply.
5
