Marantz SR4600 Connecting Multi Channel Audio Source, Connecting AN External Power Amplifier

Models: SR4600

1 41
Download 41 pages 33.57 Kb
Page 17
Image 17

ENGLISH

ADVANCED CONNECTING

 

CONNECTING THE REMOTE CONTROL JACKS

R L R L

L R

CENTER

 

L

 

R

 

FRONT SURR. SUB

SURR.

WOOFER

BACK

POWER

AMPLIFER

R L R L L R

 

 

 

 

VIDEO

 

 

 

 

 

 

 

 

 

 

 

FM (75)

GND

AM

 

 

IN

OUT

IN

OUT

 

 

MONITOR

IN VCR1OUT

DVD

MONITOR

ANTENNA

 

 

 

DSS / VCR2

 

VCR1

DVD

TV

L

SL

C

SBL

 

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IN

OUT

IN

OUT

IN

OUT

IN

OUT

 

 

R

SR

SW

SBR

1

CD

TAPE

CDR/MD

DSS / VCR2

VCR1

DVD

TV

7.1CH INPUT

 

 

 

 

AUDIO

 

 

 

 

 

AUDIO

 

 

 

 

 

 

 

PRE OUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RC-5

COMPONENT VIDEO

 

 

 

 

 

 

S-

 

 

 

 

 

 

 

 

 

VIDEO

 

 

 

 

 

 

IN VCR1OUT

 

 

 

 

 

 

Y

TV

MONITOR

DVD

MONITOR

 

IN

OUT

 

 

L

SL

C

SBL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CB/PB

 

 

 

 

 

 

 

 

 

 

CR/PR

 

R

SR

SW

SBR

1

2

OPT.

3

4

COAX.

TV

 

7.1CH INPUT

 

 

 

OUT

 

 

OUT DVD DSS / VCR 2 MONITOR

 

 

 

 

 

 

 

DIGITAL

 

AC IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UNSWITCHED

 

 

 

 

 

 

 

 

 

 

1A 120W MAX

R

L

R

L

 

 

 

 

 

 

 

RROUND BACK

SURROUND

 

CENTER

 

 

 

 

SWITCHED

. SPEAKER B

 

 

 

 

 

 

 

 

1A 120W MAX

NIMUM 6 OHMS

 

 

 

 

 

 

 

AC OUTLETS

 

 

 

 

 

 

 

 

 

 

120V 60HZ

2

RC OUT

OPTION

Subwoofer

Front Center Front

LeftRight

Surround Surround

LeftRight

L

SL

C

SBL

 

 

 

 

 

 

 

 

 

R

L

R

L

R

L

 

 

 

 

 

FRONT

SURROUND BACK

SURROUND

CENTER

R

SR

SW

SBR

 

S. SPEAKER B

 

 

 

SPEAKER SYSTEMS MINIMUM 6 OHMS

L R R L R L

1

REMOTE

CD RECORDER

REMOTE

MD DECK

REMOTE

CD PLAYER

CONTROL

 

CONTROL

 

CONTROL

 

IN

 

IN

 

IN

 

OUT

 

OUT

 

OUT

 

 

EXTERNAL INTERNAL

 

EXTERNAL INTERNAL

 

EXTERNAL INTERNAL

Surround

Surround

L R

L R

 

L R

 

 

 

 

Back Left

Back Right

 

 

 

 

 

 

 

 

CENTER

 

 

 

L

 

 

 

 

 

R

 

 

 

 

 

FRONT

SURR.

SUB

SURR.

 

 

 

 

WOOFER

BACK

DVD AUDIO PLAYER

or

SACD MULTI CHANNEL PLAYER

q

You can control other Marantz products through this unit with the remote control by connecting the REMOTE CONTROL terminals on each unit.

The signal transmitted from the remote control is received by the remote sensor on this unit. Then the

w

Whenever external infrared sensors or similar devices are connected to RC-5 IN of the SR4600, be sure to always disable operation of the infrared sensor on the main unit by using the following procedure.

CONNECTING MULTI CHANNEL AUDIO SOURCE

The 7.1CH INPUT jacks are for multichannel audio source such as a SACD multichannel player, DVD audio player or external decoder.

If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the 7.1 channel input level menu. See page 29.

CONNECTING AN EXTERNAL POWER AMPLIFIER

The PREOUT jacks are for connecting external power amplifiers.

Be sure to connect each speaker to the corresponding external power amplifier.

signal is sent to the connected device through this terminal. Therefore you only need to aim the remote at one unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier’s, power switch is synchronized with this unit’s power switch.

Set the REMOTE CONTROL SWITCH on the units, other than the main unit to EXT.(EXTERNAL) for this feature.

1. Hold down the 7.1CH INPUT button and MENU button on the front panel at the same time for five seconds.

2. The setting “IR=ENABLE” is shown on the FL DISPLAY.

3. Press the or cursor button to change this to “IR=DISABLE”.

4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled.

Note:

Be sure to set to “IR=ENABLE” when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands.

5. To restore the original setting, perform steps 1 to 4 to set to “IR=ENABLE”.

14

Page 17
Image 17
Marantz SR4600 manual Connecting Multi Channel Audio Source, Connecting AN External Power Amplifier