Marantz SR7200 manual Programming the JOG Dial, If Full is displayed on the LCD

3.Press the DVD Function button ,.

ENGLISH	C D	DVD		CD-R/MD
	DSS	T V		VCR	AUX
	L D	TUNER	TAPE		AMP
	CLEAR	MEMO		GUIDE	MUTE
	AUTO	DTS		CS5.1	6.1

4.Press the PLAY button ⁄0(3 OK). The LEARN indicator changes from blinking to continuously lit.

CH OK VOL

C D DVD CD-R/MD

5.Press and hold the PLAY button on the DVD player’s remote controller. The remote controller has finished learning the command when OK appears on the LCD a.

•If AGAIN appears on the LCD, some error has prevented the command from being learned. If this happens, simply repeat the procedure from step 4.

•In the rare event that NG appears on the LCD, it means that the remote controller you are attempting to learn from uses special signals that cannot be learned by the Marantz remote controller.

6.Follow the same procedure to make the remote controller learn the ten-key ⁄7operation used by the DVD player’s remote controller.

7.Repeat the procedure from step 3 to have the remote controller learn the signal codes for the other components such as TV, VCR, etc.

•If no buttons are pressed for approximately 1 minute while in the LEARN mode, the remote controller automatically returns to the USE mode.

•When programming the function buttons, first switch to the desired function, then press the button again.

8.When you have finished programming the remote controller, use a ballpoint pen or other sharp point to once again press the MODE button z to return it to the USE mode. The LCD displays the USE indicator, and the newly programmed codes now can be used.

If FULL is displayed on the LCD

If FULL is displayed on the LCD b when programming in the LEARN mode, it means that the memory has become too full to hold any further codes.

If FULL is displayed no matter how many times you attempt to enter new codes, it means that the remote controller cannot accept any new codes until some of the previously learned codes are deleted to make space in the memory. Select unneeded codes for each of the Jog Dial control n and Function buttons ,, which show FULL and delete them from the memory.

Note:

The power ON and OFF buttons c can only be programmed to learn one type of code, regardless of the function button that has been selected.

PROGRAMMING THE JOG DIAL

Let’s use the example of setting as the TITLE code for the DVD player.

1.Use a ballpoint pen or other sharp point to press the MODE button z until the LEARN indicator is displayed and starts to blink.

2.Place the DVD player’s remote controller so that its infrared transmitter window is facing the infrared signal receiver window on the Marantz remote controller at a distance of about 5 centimeters (2 inches).

3.Press the DVD Function button ,.

4.Rotate the Jog Dial n left or right until is displayed, then press the ENT button m.

• The LEARN and NAME indicators will both be displayed.

5.Press the TITLE button on the DVD player’s remote controller continuously until OK is displayed on the Marantz remote controller’s LCD, indicating that the programming has been completed.

•If AGAIN appears on the LCD, some error has prevented the command from being learned. If this happens, simply repeat the procedure from step 4.

When the programming has been completed, the remote controller automatically switches to the NAME mode.

The left hand position on the LCD b blinks, indicating the character in the name to be rewritten.

•If you do not wish to rewrite the name, simply press the OK Cursor button ⁄0.

•If you wish to rewrite the name, input the desired characters using the ten-key pad ⁄7. The part of the display that is being rewritten may be selected using the < and > Cursor buttons ⁄0. When you are finished rewriting, press the OK Cursor button ⁄0.

To simply erase already existing characters, press the 0 button to replace them with a blank space.

(Refer to next section on rewriting names)

6.Use the same procedure to program the codes for other 1-6 with the Jog Dial n.

7.When finished programming the codes for each of the buttons, use a ballpoint pen or other sharp point to press the MODE button z to return the remote controller to the USE mode. Once USE is displayed on the LCD, the newly memorized codes are available for use.

20