REWRITING NAMES
This remote controller allows the names accessible by Jog Dial control n to be rewritten with new ones of your choosing.
•Rewriting of names is performed for each individual function.
•Let’s use a DVD player as an example to show how to change the
’s “OSD” to
1.Use a ballpoint pen or other sharp point to press the MODE button z to switch the remote controller to the NAME mode. The NAME indicator blinks.
2.Press the DVD Function button ,.
C D | DVD | |||
DSS | T V |
| VCR | AUX |
L D | TUNER | TAPE | AMP | |
CLEAR | MEMO |
| GUIDE | MUTE |
AUTO | DTS |
| CS5.1 | 6.1 |
3.Use the Jog Dial n to select the page for which you wish to enter a new name.
4.The character on the
Use the < and > Cursor buttons ⁄0to select the characters to be rewritten.
7. Follow the same procedure to enter | ENGLISH | |||
the OK Cursor button ⁄0. Pressing OK permanently fixes the | ||||
| ||||
newly written characters. |
| |||
|
|
|
| |
|
|
|
|
•Up to 5 alphanumeric characters may be entered in the Command Name indicator of the LCD.
•To rewrite the names of the other items in the Command Name indicator, use the Jog Dial n to select the desired command and repeat from step 5.
8.When you are finished rewriting, use a ballpoint pen or other sharp point to press the MODE button z to return the remote controller to the USE mode. The USE indicator is displayed on the LCD, and the newly programmed codes now can be used.
POWER
SOURCE
ON ON / OFF OFF
LEARNING REMOTE
CONTROL RC 7200SR MACRO MODE
5.Use the
Pressing the number buttons on the
Ten keypad | Press, press again, press again, etc. |
1A → B → C → 1 → A
2D → E → F → 2 → D
3G → H → I → 3 → G
4J → K → L → 4 → J
5M → N → O → 5 → M
6P → Q → R → 6 → P
7S → T → U → 7 → S
8V → W → X → 8 → V
9Y → Z → / → 9 → Y
0SPACE → + → — → , → ’ → 0 →SPACE ()
6.For example, to enter the letter “F”, press the
Once the desired character “F” appears, press either of the < and
>Cursor buttons ⁄0and the “F” will be permanently written over the former character. Press the
ERASING PROGRAMMED CODES
(Returning to Factory Presets)
Codes that have been programmed into the memory can be erased in 4 ways: by button(s), by function(s), by Jog Dial command, and by erasing all memory contents.
1.Use a ballpoint pen or other sharp point to press the MODE button z to switch the remote controller to the LEARN mode, so that the LEARN indicator is blinking on the LCD.
Note:
Erasing of programmed codes is only possible in the LEARN mode.
2.Erasing by Button(s)
To erase the codes and names programmed for any button, press and hold the CLEAR button ⁄5, then press the button to be erased twice. This will return the button to its factory presets or leave it empty if no factory presets are available.
Jog Dial codes may be erased in the same way, by pressing and holding the CLEAR button ⁄5while using the Jog Dial n to call up the command to be erased, then pressing one of the ENT buttons m on either side of the Jog Dial n twice. This will return the button to its factory presets or leave it empty if no factory presets are available.
To erase codes programmed for the CLEAR button ⁄5, simply press the CLEAR button ⁄5continuously for 3 seconds.
As an example, let’s clear the PLAY command from the DVD player command set.
ENT | ENT |
CH | OK | VOL |
C D |
| DVD | |||
DSS | T V |
|
| VCR | AUX |
L D | TUNER | TAPE | AMP | ||
CLEAR | MEMO |
|
| GUIDE | MUTE |
AUTO |
| DTS |
| CS5.1 | 6.1 |
1 | 2 | 3 |
| 4 | 5 |
21