Marantz SR7200 manual Editing Macros, Using Macros

3.Press the buttons for the operations you wish to program as a macro in the sequence you want the macro to program them. The name of the button pressed appears on LCD a. The number of steps in the macro is displayed on LCD c and this number increases by 1 with each button pressed.

For example, press DVD, PLAY.

Each function button can be programmed to perform up to 10 steps in sequence.

•If, while programming, no buttons are pressed for approximately 1 minute, the remote controller will automatically return to normal mode, and no macro will be programmed in the memory.

CH OK VOL

C D	DVD		CD-R/MD
DSS	T V		VCR	AUX
L D	TUNER	TAPE		AMP
CLEAR	MEMO		GUIDE	MUTE
AUTO		DTS	CS5.1	6.1
1	2	3	4	5
DSP 6-STEREO		2CH	OSD	SLEEP
6	7	8	9	0

4.When you are finished programming macros, use a ballpoint pen or other sharp point to press the MACRO button x. LCD a will

display END, and the display will return to normal.

• Macros cannot be programmed for the MODE z, MACRO x, < • 3 ⁄1, VOL / ., MEMO ⁄6or CLEAR ⁄5buttons.

In the macro mode it is possible to program the memory to perform macros containing up to 10 steps.

Each of the function operations (11 including CD, CD-R, etc.) can be used in a macro more than once, however for all except AMP, only the first function operation will be transmitted as a signal from the remote controller . Accordingly, within a single macro, it is not possible to switch between multiple function operations. (This is to prevent the switching of the receiver function operation.) Within a macro, the second time a function operation is used, it will only be used on the remote controller itself and no signal will be transmitted to the component.

EDITING MACROS

Macros may be edited using following procedure.

1.Use a ballpoint pen or other sharp point to press the MACRO button x until the MACRO and LEARN indicators are displayed blinking on the LCD.

2.Press the Function button , to be changed. Let’s use the example of the DVD player, by pressing the DVD Function button

,.

•DVD-Mis displayed blinking on LCD a.

•The number of steps in the completed macro is highlighted on LCD c. In this example there are 3 macro programs in memory.

The is highlighted if no macros have been programmed, and the remote controller is ready for macro programming.

3. While pressing the VOL button ., use the ^ and v Cursor			ENGLISH
buttons ⁄0to call up the portion of the macro to be changed.
Pressing the ^ button advances through the macro steps and
pressing the v button regresses through the macro steps.
CH	OK	VOL
C D	DVD	CD-R/MD
DSS	T V VCR	AUX

•To rewrite an existing macro step, simply press the button for the new step. The old step will be erased and rewritten with the new step.

•To insert a new step in between existing steps in a macro, after step 3 press the MEMO button ⁄6, then press the button for the new step. The numbers of the other steps will be adjusted accordingly to accommodate the new step. Since only 10 steps may be stored in any macro, the tenth step will be erased if an step is inserted when the total number of steps is already 10.

L D	TUNER		TAPE	AMP
CLEAR	MEMO		GUIDE	MUTE
AUTO		DTS	CS5.1	6.1
1	2	3	4	5
DSP	6-STEREO	2CH	OSD	SLEEP
6	7	8	9	0

•To erase a step in a macro, after step 3 call up the number of the step to be erased and press the CLEAR button ⁄5.

L D	TUNER		TAPE	AMP
CLEAR	MEMO		GUIDE	MUTE
AUTO		DTS	CS5.1	6.1
1	2	3	4	5
DSP	6-STEREO	2CH	OSD	SLEEP
6	7	8	9	0

•If while editing macros no buttons are pressed for approximately 1 minute, the remote controller will automatically return to normal mode, and no macro changes will be programmed in the memory.

4.When you are finished editing macros, use a ballpoint pen or other sharp point to press the MACRO button x. END will be displayed on LCD a and the display will return to normal.

USING MACROS

The following procedure will show how to use the function buttons for which you have programmed macros.

1.Press the Function button , for the desired macro for 3 seconds. MACRO is displayed on LCD a for approximately 1 second, after which the number of steps in the macro is displayed on LCD c.

C D	DVD		CD-R/MD
DSS	T V		VCR	AUX
L D	TUNER	TAPE		AMP
CLEAR	MEMO		GUIDE	MUTE
AUTO	DTS		CS5.1	6.1

•The remote controller will do nothing if no macros are programmed. The macro steps are executed in order and the names of their buttons are displayed on the LCD. Also, the step numbers displayed on LCD c disappear as each step is executed.

2.After all macro commands have been transmitted, the remote controller returns to normal mode.

•To cancel the transmission of a programmed macro, use the Cursor buttons ⁄0to press 7.

23