INSTALLATION
3
ing from the drain line.
Observe cooker operation for several minutes. Op-
eration is correct if timer dials begin to rotate after a
short delay period required for preheating. After the
delay period plus the “4 minute” initial setting, the
timer dials will return to the “0 minute” position, at
which a buzzer sounds. The buzzer is silenced by
turning the dial to the OFF position.
SHUT-DOWN PROCEDURE:
No shut-down procedure is required for the Pressure-
less Cooker except to check that all timer dials (2) are
in the OFF position and the compartment doors are
open. Consult the steam boiler instruction plate and
complete the shut-down procedures for the boiler.
REVERSING THE DOORS:
The Pressureless Steam Cooker has a reversible
cooking compartment door. This section contains in-
structions for reversing this door.
Open the cooking compartment door.
Remove the two screws that attach the top hinge
to the front of the unit.
Slide the door upward, off the bottom hinge.
Remove the two screws that attach the bottom
hinge to the front of the unit.
Remove the plastic hole plugs from the front of
the unit. Push the black hole plugs into the left-up-
per and -lower hinge mounting holes.
Reinstall the top hinge with spacers and screws
into the right-lower hinge mounting hole.
Rotate the hinge 180° for installation, so that the
pin that the door rides on is now facing UP.
Remove the door latch assembly from the face
of the unit. The two nuts mounting the door latch
are located behind the face of the unit and must
be accessed by removing the control panel. First
4.
1.
2.
3.
4.
5.
6.
7.
shut off the power to the unit at its source then
remove the control panel by unscrewing the eight
mounting screws and pulling the panel away from
the front frame.
Remove the two white hole plugs from the left
door latch mounting holes, and insert them into
the right door latch mounting holes (where the
door latch assembly was originally mounted).
Rotate the door latch assembly 180°, and install
into the left door latch mounting holes.
NOTE: Each stud on the latch assembly should
have a plastic washer, a spring, a plastic washer,
and a Nyloc type nut.
To adjust the tension of the door latch, tighten both
nuts down until the springs are fully compressed,
then back each nut off 1/2 turn.
Replace the control panel, and reconnect the
power to the unit.
Remove the inner door assembly by removing the
six screws and spacers on the top and bottom of
the door.
Move the magnet and magnet clip to the opposite
side of the inner door panel (see g. 5, page 20).
Put the door back together, making sure the mag-
net is located at the top of the door, and refasten it
together with the six screws and spacers into the
top and bottom of the door.
Rotate the door 180° for mounting.
Slide the remaining hinge into the top door bear-
ing.
Slide the door and hinge assembly down onto the
hinge that you have already mounted to the front
of the unit. Use the two to mount the top hinge into
the right upper hinge mounting holes.
NOTE: Be sure to include spacer washers behind
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
OPERATING CONTROLS AND INDICATORS:
The controls and indicators required to operate the
Pressureless Steam Cooker are listed in Table 1 on
page 5, together with a short functional description of
each. Figure 1 on page 5 shows the physical location
of each control and indicator.
OPERATING PROCEDURES:
The 3500 Pressureless Steam Cooker defrosts fro-
zen foods and cooks fresh and defrosted foods. Each
cooking compartment permits selection of continuous
(constant steam) cooking or timed (0–60 minutes)
cooking. Instructions for operation are included in
this section. Consult Test Kitchen Bulletin for detailed
cooking information.
OPERATION