Bluetooth Pcb, 11-16 | Matsushita CF-30 instruction

BLUETOOTH PCB

Q 203,			UNR9213J0L	TRANSISTOR	1

R 200, 206,			ERJ2GEJ473X	RESISTOR, 1/16W, 47KΩ	2
R 203, 205, 207, 209, 210,			ERJ2GEJ102X	RESISTOR, 1/16W, 1KΩ	12
211 212	217 220 221
R 208,			ERJ2GEJ273X	RESISTOR, 1/16W, 27KΩ	1

R 213, 214, 215, 216,			ERJ2GEJ822X	RESISTOR, 1/16W, 8.2KΩ	4

R 218,			ERJ2GEJ512X	RESISTOR, 1/16W, 5.1KΩ	1

R 226,			DEARA8AJ473M	RESISTOR ARRAY	1

R 227, 228,			ERJ2GEJ270X	RESISTOR, 1/16W, 27Ω	2

R 229,			ERJ2GEJ152X	RESISTOR, 1/16W, 1.5KΩ	1

X 200,			H2D600400005	OSCILLATOR, 6MHz	1

BLUETOOTH PCB

C 1,		F1J0J106A016	CAPACITOR, 6.3V, 10µF	1

C 2, 4, 7, 11,		F1G1C104A042	CAPACITOR, 16V, 0.1µF	4

C 3, 5,		F1G1H102A496	CAPACITOR, 50V, 1000pF	2

C 6, 9,		F1G1E103A062	CAPACITOR, 25V, 0.01µF	2
C 8,		F1G1H270A542	CAPACITOR, 50V, 27pF	1

CN 1,		K1MN10BA0070	CONNECTOR	1
IC 1,		C0JBAZ002422	IC, FET SWITCH	1

IC 2,		N5HZZ0000040	BLUETOOTH MODULE	1
IC 3,		C0EBE0000460	IC	1

KJ 1,		K1QZA1AE0001	CONNECTOR	1
L 1, 2,		J0JJC0000015	INDUCTOR	2

L 4,		G1C5N6ZA0029	INCUCTOR	1
L 5,		J0MAB0000200	INDUCTOR	1

Q 1,		B1GBCFJN0037	TRANSISTOR	1
Q 2,		B1DHDC000028	TRANSISTOR	1

R 1, 2,		ERJ2GEJ104X	RESISTOR, 1/16W, 100KΩ	2

11-16

Image 81

Matsushita CF-30 service manual Bluetooth Pcb, 11-16

Contents

Model No. CF-30 SERIES This is the Service Manual for the following areas E …for U.KNotebook Computer Model No. CF-30CTQAZ 1 How to replace the fuse For U.K This apparatus must be earthed for your safetyOpen the fuse compartment with a screw- driver and replace the fuse LASER SAFETY INFORMATION Page Page CONTENTS Main Specifications 1 Specifications Wireless LAN Only for model with wireless LAN BluetoothTM Only for model with Bluetooth23-E-1 2 Names and Functions of Part C D E F G Q J H K L M N O P RRight side CF-30 Block Diagram Diagram3 Block Intel Core 4.1. Basic Procedures 4 Diagnosis Procedure Flow Chart 4.2. Troubleshooting 5 Power-On Self Test Boot Check Error Diagnosis by Checking Beep Signal SoundOutline of POST 6 List of Error Codes Only when the port replicator is connected 02F0 CPU ID 1. Beginning of self-diagnosis test 1-1. Setting of content of setup 7 Self Diagnosis Test1-2. When you execute an automatic test 1-3. When you execute the enhancing test 2. Operation of PC-Diagnostic Utility 2-2. PC-Diagnostic utility End method 2-3. The content of the setup is returned to the setting of the user2-1. Selection of tested device 7.1. Test Item and Division of trouble EnhancingPlace with possibili Test Item 8 Wiring Connection Diagram Disassembly Instructions 9 Disassembly/Reassembly9.1.2. Removing the Battery Pack and HDD 9.1.1 9.1.3. Removing the HDD 9.1.4. Removing the KB Cover, Hinge Cover L, Hinge Cover R and Keyboard 9.1.6. Removing the GPS PCB and Blue- tooth PCB 9.1.5. Removing the KB Cable Cover and LCD Cable Cover 9.1.8. Removing the USB PCB and Antenna PCB 9.1.7. Removing the DIMM Cover and Bot- tom Cover 9.1.9. Removing the FPC HDD BAT 9.1.10. Removing the PAD PCB9.1.11. Removing the Main PCB CN400,CN401 11. Remove the 2 Screws. N5 12. Remove the 2 Screws. N21 9.1.13. Removing the I/O PCB 9.1.12. Removing the SD PCB, Express Cardand PCMCIA Card 1. Open the Connector Cover and Lid Cover 9.1.15. Removing the Handle and Power SW 9.1.16. Removing the Display Unit 9.1.17. Removing the LCD Rear CabinetHinge L and R 9.1.19. Removing the Antenna PCB L and R 9.1.18. Removing the Inverter PCB, TS PCB and LCD Unit 9.2.1. Attention when CF-30 series is repaired 9.2. Reassembly Instructions9.2.2. Setting the Antenna PCB L and R Safety Working Inverter-PCB 9.2.3. Setting the Inverter PCB, TS PCB and LCD Unit 9.2.4. Setting the LCD Rear Cabinet, Hinge L and R 9.2.6. Setting the Handle and Power SW 9.2.5. Setting the Display Unit Attach the Sheet Attach the TapeSW-LED FPC Ass’y Attach it not to overlap the SW leg Q Assembly of Palm Top Cover Q Assembly of Power SW9-16 Cover Setting the SD PCB, Express Card Setting the I/O PCB9.2.8 9.2.9 9.2.10. Setting the Main PCB Connector CN27 N7 Connector CN1724. Fix the Screw. N7 25. Attach the TOP Screws 9-19 Q Assembly of Main PCB Q Assembly of LAN, Modem and MDC12 Safety Working 9-20 9.2.11. Setting the PAD PCB 9.2.12. Setting the FPC HDD BAT Page 9.2.13. Setting the USB PCB and Antenna PCB 9-25 Q Assembly of USB PCB and Antenna PCB 9.2.14. Setting the DIMM Cover and Bottom Cover Q Preparation of DIMM Cover 9-27Attach the Keyboard Cable Cover Cushion 1. Fix the GPS BT Angle and GPS PCB using the 2 Screws. N11 9.2.15. Setting the GPS PCB and Bluetooth PCB2. Connect the Cable to the Connector on GPS PCB 3. Fix the GPS Ass’y using the 4 Screws. N12 to Connector 9.2.16. Setting the KB Cable Cover, Keyboard and LCD Cable Cover 7.2.18. Setting the HDD Important Parts Heater for Safety Lead WireQ Preparation oh HDD ASSY 9-31 HDD Damper Ass’y 1. Apply the load when attaching the parts. 20N to 30N 2 to 3Kgf/cm2Push and bend HDD Ass’y HDD Thermal Plate Do not bend it at a sharp angle to put natural RKeep the space to secure the air vent B-B SEC HDD Side DamperA-A SEC Lower Case Avoid getting HDD under the side damper when inserting HDD 9.2.19. Setting the Battery Pack and HDD Pack 1. Set the HDD Pack 2. Set the Battery Pack9-36 Screw tightening torque 10 E xploded View G 1.47 ± 0.20 N.m 15.0 ± 2.0 kgf.cm L 0.2 ± 0.02 N.m 2.0 ± 0.2kgf.cm A 0.19 ± 0.02 N.m 2.0 ± 0.2 kgf.cm B 0.45 ± 0.05 N.m 4.5 ± 0.5 kgf.cmQ 0.22 ± 0.02 N.m 2.2 ± 0.2 kgf.cm R 0.30 ± 0.05 N.m 3.0 ± 0.5 kgf.cm T 0.90 ± 0.05 N.m 9.0 ± 0.5 kgf.cm Screw tightening torque R 0.3 + 0.05 N.m 3.0 + 0.5 kgf.cm S 0.19 + 0.05 N.m 2.0 + 0.5 kgf.cm B 0.45 + 0.05 N.m 4.5 + 0.5 kgf.cm P 0.8 + 0.1N.m 8.0 + 1.0 kgf.cm10-4 K2-32 K9-1-4 K10-2 E35 K54 E35-2 E15 E35-5A E35-10 K56 E35-3E35-1 E35-8 E35-4 E35-6 E35-3 E35-7 E35-4 A E35-10 E35-9 Screw tightening torque Replacement Parts List CF-30CTQAZxxREF. NO and AREA Packing Material AccessoriesMechanical Parts FAX +44-029-20736250 WIRELESS SW KNOB WIRELESS SW CASEK2-2-4 DFHR6257ZA WIRELESS SW FPC POWER SW CUSHIONK2-10-4 DFHR3E58ZA DFWV84A0277 K9-2TOUCH SCREEN PANEL KIT K9-2-1 DFMC0863ZA POWER SW LED PANELINV SHIELD CASE DFMC0873ZA DFMD4067ZA-0 K122SERIAL COVER PLATE K123 Replacement Parts List Note Important Safety Notice11-8 F1G1A104A014 11-9 11-10 D 8, 9, 10, 11, 12, 13, 14IC 32, 58, 59, 61, 62, 68 IC 65, 72, 96, 101, 102 11-11Q 1, 2, 36, 52, 53, 59, 66 Q 3, 4, 16, 30, 31, 32, 33 R 21, 47, 99, 100, 101 11-12R 40, 104, 109, 136, 150 R 49, 117, 151, 152, 209 R 170 11-13 IO PCB MP PCB11-14 P-SW PCB SD PCBBAT FPC HDD PACK PCB 11-16 BLUETOOTH PCB