Manuals / Maxtor / Computer Equipment / Computer Drive

Maxtor VL 17 manual System Hangs During Boot

Models: VL 17

1 71

Download 71 pages 22.37 Kb

Page 32

INSTALLATION

9 System Hangs During Boot

If the system hangs during the boot process after installing the Maxtor hard drive – either before or after setting the system BIOS – the system many have a BIOS with a cylinder limitation. This may occur for hard drives that exceed 2.1 GB. If this happens,

do the following:

1Turn the system OFF.

2Install the cylinder limitation jumper (J46) on the drive. The figure below shows the Maxtor hard drive configured as a Master or Slave device with the cylinder limitation jumper installed.

IMPORTANT: When the Cylinder Limitation jumper (J46) is installed, the Maxtor hard drive must be prepared using MaxBlast installation software.

3If the BIOS was set to AUTO DETECT, follow the instructions in Section 7 to prepare the hard drive using the MaxBlast installation software.

If other BIOS settings were used, access the system BIOS SETUP program and set the parameters to aUserDefinableTypewith 4,092 cylinders, 16 heads and 63 sectorspertrackfortheMaxtorharddrive.ThenfollowtheinstructionsforsettingtheBIOSinSection7thenSection8topreparetheharddrivewithMaxBlastsoftware.

4 – 10

Image 32

Maxtor VL 17 manual System Hangs During Boot

Contents

HA RD Drive Produc T MA Nual DiamondMaxVL REV EC no Section Description Date Before You Begin U T I O N Contents Product Specifications Handling and Installation AT Interface Description Host Software Interface Glossary Interface CommandsService and Support Figures Introduction Maxtor CorporationManual Organization Abbreviations Signal Conventions ConventionsKey Words Numbering DiamondMax VL 17 Key Features Product Description Product Features Functional / Interface Defect Management Zone DMZ On-the-Fly Hardware Error Correction Code ECCLogical Block Addressing Cache Management Major HDA Components Subsystem Configuration Jumper Location/ConfigurationCylinder Limitation Dual Drive Support Product Specifications Drive ConfigurationPerformance Specifications Models and Capacities Physical Dimensions Parameter Standard Metric Power Requirements Power Mode DefinitionsEPA Energy Star Compliance Environmental Limits Reliability Specifications Shock and Vibration Canadian Emissions Statement Safety Regulatory ComplianceRadiated Electromagnetic Field Emissions EMC Compliance Handling and Installation Hard Drive Handling PrecautionsPre-formatted Drive Important Notice Unpacking and Inspection Multi-pack Shipping Container Repacking Physical InstallationRecommended Mounting Configuration Handling Precautions Tools for InstallationSystem Requirements Drive Identification Information General Requirements Hard Drive Identification Systems Using Cable Select Installing 5.25-inch Mounting Brackets and RailsInstalling in a Device Bay Mounting Drive in System Attaching Interface and Power Cables Attaching System Cables Bios Cmos Parameters System SetupSetting the Bios Cmos Hard Drive Preparation System Hangs During Boot Interface Connector PIN SignalAT Interface Description Pin Description Summary PIN Name Signal Name Signal Description Pin Description Table Timing Parameters Mode PIO Timing DMA Timing Mode MIN MAX Ultra DMA Timing Sustained Ultra DMA Data In Burst Device Terminating an Ultra DMA Data In Burst Initiating an Ultra DMA Data Out Burst Device Pausing an Ultra DMA Data Out Burst Device Terminating an Ultra DMA Data Out Burst Error Register Features RegisterHost Software Interface Task File Registers Sector Count Register Sector Number RegisterCylinder Number Registers Device/Head Register Command Register Summary Command Name Command Code Parameters UsedTimer Value TIME-OUT Period Control Diagnostic Registers Alternate Status RegisterDevice Control Register Digital Input Register Interrupt Handling Reset and Interrupt HandlingReset Handling Interface Commands Set Feature Commands Read Verify Sectors Read CommandsRead Sectors Read DMA Read Multiple Write Commands Set Multiple ModeWrite Sectors Write Verify Sectors Write Multiple Write DMA Value Description Set Feature CommandsSet Features Mode Power Mode Commands Sleep Mode Identify Drive Initialization CommandsWord Content Description 15-8 = PIO data transfer mode = Write Cache enabled Initialize Drive Parameters Seek, Format and Diagnostic Commands Execute Drive DiagnosticError Code Description Format Track A.R.T. Command Set Execute S.M.A.R.T Service and Support Service PolicyNo Quibble Service Support Internet MaxFax ServiceCustomer Service Access Time Glossary Cylinder Zero Gigabyte GB Logical Block Addressing Read Gate Signal THIN-FILM Media