![](/images/new-backgrounds/1293496/29349631x1.webp)
TO MAKE ELECTRICALCONNECTIONFOR U.S. DRYERS
Reviewelectrical requirements on page 6 of these instructions.
12, For electric dryers:
CONNECTION. The dryer frame is grounded to the neutral conductor
at the terminal block. A
not permit groundingthrough neutral. If the
the dryer frame cannot be grounded to the neutral conductor at the terminal block. Refer to the following instructionsfor 3- and
SYSTEM CONNECTIONS.
I |
|
/®l _er_ | I® |
_ _ | |
/ | O |
,Figure 25 |
|
B
Removethe terminal block cover plate. (See figure 25.) | II | i |
|
A protectiveconduit (plastic)is providedfor the power cord. Cut the |
|
|
|
conduit so that it is approximately18 inchesshorterthan the power |
|
|
|
cord and thread the power cord through the conduit. (See figures26 & |
|
|
|
27.) |
|
|
|
Insert the power cord with a U.L. listed strain reliefthrough the hole | Figure 26 |
|
|
provided in the cabinet near the terminal block. Note, a strain relief |
|
|
|
must be used. |
|
|
|
|
|
|
|
Do not loosenthe nuts already installed on the terminal block. Be |
|
|
|
sure they are tight. Use a 3/8 inch deep nut driver. |
|
|
|
If the power cord hasterminals, place the terminals over the existing |
|
|
|
nuts on the posts. The neutral (white or center wire on power cord) | Figure27 |
|
|
conductormust always be connectedto the center (silver colored) |
| ||
post of the terminal block. |
| ||
Secure in place using the nuts provided in the parts oackage. If the |
| Cord Attached | |
,__,,_Power |
| ||
power cord does not haveterminals, use the cupped washers ahead |
|
|
|
of the nuts. |
|
| Ground |
Be sure the terminal block nuts are tight. Secure the power cord in |
|
|
|
position. Tightenthe strain reliefscrew(s) in order to clamp the strain |
|
|
|
reliefto the cord. (See figure 28.) |
|
|
|
Replacethe terminal block cover. |
|
| Neutral |
BEFOREOPERATINGOR TESTING,follow the grounding directions |
|
|
|
on page 5. |
|
| Strain |
|
| relief | |
Removethe ground strap screw from the terminal block support. Fold | Figure 28 |
|
|
the ground strap over so both ends of the ground strap are attached |
|
|
|
to the center terminal block post. |
|
| |
Connectthe neutral (white)conductor of the cord to the center (silver) | Power Supply Attached | ||
post of the terminal block. Connectthe grounding (green) wire of the |
|
|
|
cord to the terminal block support using the ground strap screw. | ° | Folded | |
Connectthe red and black wires of the cord to the outer posts of the | Neutral _ | _.'_'_ | Ground |
terminalBesuretheblockterminal. block nuts are on tight. Secure the power cord in | Post |
| Strap |
positiOnReplacetotheTightencord.reliefterminal(seeblock, Straincoverfigure. relief29in order.)screw(s)to clamp the strain | •///__ |
| /e NStraineutral |
WARNING: If convertingfrom |
| o _ | Relief |
ground strap must be reconnectedto terminal block supportto ground |
| (_ | 4''/ |
the dryer frame to the neutral conductor. | Figure 29 |
|
|
Page 15