Tools needed for securing the drain hose and leveling the washer:

Adjustable or open end

Wood block

 

wrench ⁹⁄₁₆" (14 mm)

Ruler or measuring tape

 

Level

 

 

Alternate Parts

Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free number on the cover or in the “Assistance or Service” section.

If You Have:

You Will Need to Buy:

Laundry tub or standpipe taller

Sump pump system (if not already available)

than 96" (2.4 m)

 

 

 

1" (2.5 cm) diameter standpipe

2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe

 

adapter, Part Number 3363920 and connector kit Part

 

Number 285835

 

 

Overhead sewer

Standard 20 gal. (76 L) 39" (99 cm) tall drain tub or

 

utility sink, sump pump and connectors (available

 

from local plumbing suppliers)

 

 

Floor drain

Siphon break, Part Number 285834; additional drain

 

hose, Part Number 8318155 and connector kit,

 

Part Number 285835

 

 

Water faucets beyond reach of fill

2 longer water fill hoses:

hoses

6 ft (1.8 m) Part Number 76314,

 

10 ft (3.0 m) Part Number 350008

 

 

Lint clogged drain

Drain protector, Part Number 367031

Location Requirements

Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”

Your washer can be installed in a basement, laundry room, closet, or recessed area. See “Drain System.”

IMPORTANT: Do not install or store the washer where it will be exposed to the weather. Proper installation is your responsibility.

You will need:

A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer. See “Electrical Requirements.”

Hot and cold water faucets located within 3 ft (90 cm) of the hot and cold water fill valves, and water pressure of 20-100 psi (138-690 kPa) for best performance.

A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on carpeting is not recommended.

A sturdy floor to support the washer weight (washer, water and load) of 315 lbs (143 kgs).

Do not store or operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See “Washer Care” for winterizing information.

Installation spacing for recessed area and closet installations

The following spacing dimensions are recommended for this washer. This washer has been tested for installation with spacing of 0" (0 cm) clearance on the sides. Recommended spacing should be considered for the following reasons:

Additional spacing should be considered for ease of installation and servicing.

Additional spacing should be considered on all sides of the washer to reduce noise transfer.

For closet installation with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Companion appliance spacing should also be considered.

 

 

3"*

14"* max.

48 in.2 *

(7.6 cm)

(35.6 cm)

 

17"*

(310 cm2)

 

 

 

(43.2 cm)

 

 

 

2

 

 

24 in. *

3"*

 

(155 cm2)

 

 

(7.6 cm)

1"

 

 

 

 

27¹⁄₂"

 

 

 

1"

 

 

1"*

 

 

27"

 

 

5"*

 

 

 

(2.5 cm)

 

(69.9 cm)

 

(2.5 cm) (2.5 cm) (68.6 cm) (12.7 cm)

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

B

 

 

 

C

A. Front view

B. Side view

C. Closet door with vents

*Required spacing

5

Page 5
Image 5
Maytag W10092684A manual Location Requirements, Alternate Parts, You will need, If You Have You Will Need to Buy