Memorex URC 4880 manual RE-ASSIGNING Device Keys, Changing Volume Lock

RE-ASSIGNING DEVICE KEYS

The One For All 4-Device Video Expert Plus With Learning remote control can be set up to control a second TV or VCR, or any combination of four video compo- nents. For example, to have the unit control a TV, a Cable Converter, and two VCRs, you will need to re-assign the unused DVD key to operate the second VCR as follows:

1. On the remote control, press and hold SET until the LED blinks twice, then release SET.

2. Enter 9 - 9 - 2. The LED will blink twice.

3. Press VCR once, then press DVD once. The LED will blink twice.

4.Program the DVD key as a second VCR. See Programming VCR Control on page 12.

To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the following chart for a desired component:

To Re-Assign	Perform Key Sequence
VCR as 2nd TV key:	SET - 9 - 9 - 2		- TV - VCR
VCR as 2nd DVD key:	SET - 9 - 9 - 2		- DVD - VCR
VCR as 2nd Cbl/Sat key:	SET - 9 - 9 - 2		- CBL/SAT - VCR
VCR back to VCR:	SET - 9 - 9 - 2		- VCR - VCR
DVD as 2nd TV key:	SET - 9 - 9 - 2		- TV - DVD
DVD as 2nd VCR key:	SET - 9 - 9 - 2		- VCR - DVD
DVD as 2nd Cbl/Sat key:	SET - 9 - 9 - 2		- CBL/SAT - DVD
DVD back to DVD:	SET - 9 - 9	- 2	- DVD - DVD
CBL/SAT as 2nd TV key:	SET - 9 - 9	- 2	- TV - CBL/SAT
CBL/SAT as 2nd DVD key:	SET - 9 - 9	- 2	- DVD - CBL/SAT
CBL/SAT as 2nd VCR key:	SET - 9 - 9	- 2	- VCR - CBL/SAT
CBL/SAT back to CBL/SAT:	SET - 9 - 9 - 2 - CBL/SAT- CBL/SAT

Upon completion of a re-assignment,the LED will blink twice to confirm your selection.At that time,you will also need to program the remote control to control the new com- ponent (see previous sections on Programming VCR Control, Programming Cable Converter or Satellite Receiver Control,or Programming DVD Player Control).

26

CHANGING VOLUME LOCK

The One For All 4-Device Video Expert Plus With Learning remote control is preset to control the volume of a component through your TV.

If your TV is not remote controllable, or if you would like the volume to be controlled by a different component, you can change the Volume Lock setting to control a volume through a non-associated mode (e.g., through the cable in the TV mode).

To change Volume Lock to the CBL/SAT mode:

1. On the remote control, press and hold SET until the LED blinks twice, then release SET.

2. Enter 9 - 9 - 3 and then press CBL/SAT once. The LED will blink twice.

3.Now, whenever you press VOL +, VOL –, or MUTE on the remote control, the volume will be controlled by your Cable Converter or Satellite Receiver.

To change Volume Lock to the VCR mode:

1. On the remote control, press and hold SET until the LED blinks twice, then release SET.

2. Enter 9 - 9 - 3 and then press VCR once. The LED will blink twice.

3.Now, whenever you press VOL +, VOL –, or MUTE on the remote control, volume will be controlled by your VCR.

To change Volume Lock to the DVD mode:

1. On the remote control, press and hold SET until the LED blinks twice, then release SET.

2. Enter 9 - 9 - 3 and then press DVD once. The LED will blink twice.

3.Now, whenever you press VOL +, VOL –, or MUTE on the remote control, volume will be controlled by your DVD (or LD) player.

27