Rear View/ Terminal Board, RGB2 | Meridian Audio FPP-50HD20 guide

Rear View/ Terminal Board

C

E

F

G

H

I

J

K

	(		VIDEO
	VIDEO 1 I N / OUT)		VIDEO
VIDEO 3			VIDEO 2
(			AUDIO 1
MONO
)	L	R
	Y
	Cb/Pb Cr/Pr		DVD1 / HD1
(			AUDIO 2
MONO
)	L	R
	Cr/Pr	R/
	G/ Y		RGB2
	Cb/Pb	B/	/ DVD2
	HD		/ HD2
	VD
	( I N / OUT		RGB 1
	)
(			AUDIO 3
MONO
)	L	R
	DV I
	(		RGB 3
	Digital		RGB 3
	RGB
	)
	External Control
	I N
	REMOTE
	OUT

D

A B

AAC IN

Connect the included power cord here.

BEXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the (positive) speaker wire to the EXT SPEAKER terminal and the (negative)

speaker wire to the EXT SPEAKER terminal on both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

CVIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, to the video processor.

DAUDIO1, AUDIO2, AUDIO3 These are audio input terminals.

The input is selectable. Set which video image to allot them from the audio menu screen.

EDVD1 / HD1

Connect DVDs to the video processor.

FRGB2/ DVD2/ HD2

RGB2:	You can connect an analog RGB signal
	and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High
Definition sources, Laser Discs, etc.
here.
This input can be set for use with an
RGB or component source. (see page
24)	3
	3

GRGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc. here. This input can be used for Input or Output. (see page 10)

HRGB3 (DVI 24pin)

Connectthe video processorhere

IEXTERNAL CONTROL

This terminal is used when operating and controlling the monitor externally (by external control).

JREMOTE IN

Connect the remote cable* to the remote control’s remote jack to obtain wired remote control.

KREMOTE OUT

Connect the remote cable* to the REMOTE IN jack of the other display monitor to obtain wired remote control.

* The 1/8 Stereo Mini cable must be purchased separately.

Image 9

Meridian Audio FPP-50HD20, FPP-42HD20, FPP-61HD20 operation manual Rear View/ Terminal Board, RGB2

Contents

Digital Cinema Series Precautions Important InformationRisk of Electric Shock Do not Open Plasma monitor cleaning procedure Use only with120V50/60HzAC powerTo avoid damage and prolong operating life Recommendations to avoid or minimize phosphor burn-in Recommandations importantes PrécautionsMises en garde et précautions de sécurité Méthode de nettoyage du moniteur à plasma Contents Ventilation Requirements for enclosure mounting How to Attach Options to the Plasma Monitor Receives the signals from the remote control Turns the monitor’s power on and offPart Names and Function Front View RGB2 Rear View/ Terminal Board Remote Control Transmits the remote control signals Battery Installation and ReplacementNot functional for the models covered in this manual Clears the number set by the ID Select button Using the wired remote control mode Handling the remote controlOperating Range Installation Connections Signal Analog Pin Assignments and Signal Levels for 15 pin RGB Analog Basic Operations To cancel the off timer To set the off timerAfter the power is turned off with the off timer To check the remaining time Wide Operations When viewing videos or digital video discs When Picture Size is set to OFF Wide Screen Operation with Computer Signals Supported resolution Picture Size setting Menu Operations Advanced menu mode Menu Tree Reset OPTION2 PWR. MGT Adjusting the picture Picture Settings Menu Picture adjustment screen Adjusting for the video processor Setting the color temperature Adjusting the color to the desired levelReducing noise in the picture Adjusting the white balance Making the Low Tone adjustments Gamma settings LOW Tone settings Adjusting the colors Audio Settings Menu Color Tune settings Audio settings menu Setting the allocation of the audio connectors Image Adjust Settings MenuAdjusting the Position, Size, Fine Picture, Picture Adj Example Setting Audio INPUT1 to Video Setting the on-screen menu Option1 Settings Menu Checking the signal being transmitted to RGB1 terminal Setting the BNC connectorsSetting a computer image to the correct RGB select screen OSM Orbiter settings Setting the Input Skip Setting high definition images to the suitable screen size Input Skip settings RGB Select modes Option2 Settings Menu Resetting to the default valuesSetting the power management for computer images Setting the picture to suit the movie POWER/STANDBY indicator PLE settings Reducing burn-in of the screen Orbiter settings Orbiter Function settings Inverse Settings Setting the time To select on for the Working TimeScreen Wiper Soft Focus settings Setting the screen size for S1/S2 video input Gray Level settings Speed Setting the signal and black level for DVI signal Setting the picture size for RGB input signals S1/S2 settings PLUG/PLAY settings Using the timer Option3 Settings Menu Present Time settings Present Time To reset the program Setting the power on mode To reset the data Special characters in the Program Timer screen PWR. on Mode settings Enabling/disabling remote control wireless transmission Control Lock settings IR Remote settings ID number setting Loop Out setting Divider settings Video Wall setting Video Wall Position settings Divider Auto ID settings DISP. Mode settings Image Adjust settings P. on Delay settings On Delay Power on delay PLE Link settings PLE Link Setting the menu mode Advanced OSM Settings MenuRepeat Timer Repeat Timer settings Color System Settings Menu Language Settings MenuSetting the language for the menus Setting the video signal format Application External ControlConnections Communication Parameters Symptom Checks Remedy TroubleshootingPage This warranty may be enforced only by the first purchaser Limited Warranty Plasma MonitorsFor More Information Telephone 408 735 Faroudja Palomar Ave Sunnyvale, CA