ENGLISH

SECTION 2 - INSTALLATION

 

VI. CONVEYOR INSTALLATION

Figure 2-12 - Removing the Conveyor Drive Sprocket

Refer to either Step A or Step B in this section, as appropriate, to install the conveyor and belt.

A. InstallingtheConveyor-AllovensEXCEPTTandem models

NOTE

Split belt conveyors can only be installed from the end of the oven with the drive motor.

Single-belt conveyor assemblies may be inserted into either end of the oven. If it is to be installed from the end of the oven without the drive motor, the drive sprocket assembly must be removed.

To remove the drive sprocket (if necessary), loosen the set screw

 

 

on the conveyor collar as shown in Figure 2-12. Then, pull the

 

 

sprocket assembly straight out.

 

Loosen conveyor collar

1. Lift the conveyor and position it in the oven as shown in

 

set screw, then pull shaft

 

straight out

Figure 2-13.

 

 

Figure 2-13 - Inserting the Conveyor

 

1

2

3

2.Continue moving the conveyor into the oven until the frame protrudes equally from each end of the oven (about 18"/ 457mm).

3.Check that the retainers located on the underside of the conveyor frame rest firmly against the lower end plug, as shown in Figure 2-14.

NOTE:

PS360EWB ovens have a retainer bracket that extends the full width of the conveyor frame on both ends of the frame. All other ovens have retainer clips as shown in Figure 2-14, located on the drive (left) side of the frame only.

4.When the conveyor is positioned properly, check for free- dom of movement of the conveyor belt by pulling it for about 2-3 feet (60 to 90 cm) with your fingers. The conveyor must move freely.

5.If the drive sprocket was removed when installing the conveyor, replace it at this time.

6.Install the drive chain between the conveyor drive sprocket and the motor sprocket. To install the chain, it will be necessary to lift the drive end of the conveyor slightly. The drive motor and sprocket are shown in Figure 2-12.

7.Install the conveyor drive motor cover and tighten its hanger screw (on the rear wall of the oven).

8.Check the tension of the conveyor belt as shown in Figure 2-15. The belt should lift between 3-4" (75-100mm). DO NOT OVERTIGHTEN THE CONVEYOR BELT.

NOTE:

If necessary, the belt tension can be adjusted by turning the conveyor adjustment screws, located at the idler (right) end of the conveyor. See Figure 2-15.

Figure 2-14 - Conveyor retainers

Retainers on both ends of

PS360EWB, drive side only for all other ovens

Figure 2-15 - Checking the conveyor tension

3-4"

(75-100mm)

vertical deflection

Conveyor

tension

adjustment

screws (idler

end only)

12

Page 11 Page 13
Page 12
Image 12
Middleby Marshall PS300F installation manual VI. Conveyor Installation, InstallingtheConveyor-AllovensEXCEPTTandem models
Page 11 Page 13

PS300F specifications

The Middleby Marshall PS300F is an advanced pizza oven designed for high-volume operations while ensuring consistent quality and superior performance. This innovative oven combines cutting-edge technology with user-friendly features, making it an ideal choice for restaurants, pizzerias, and foodservice operations that demand efficiency and speed.

One of the standout features of the PS300F is its patented airflow technology. This system is designed to circulate hot air evenly throughout the cooking chamber, which helps create a perfectly baked pizza with a crispy crust and thoroughly cooked toppings. The even heat distribution ensures that every inch of the pizza receives the same level of cooking, reducing the chances of hot or cold spots that can affect the overall quality.

The PS300F is equipped with a double-deck design, allowing for increased production capacity without requiring additional floor space. Each deck can accommodate multiple pizzas at once, making it an ideal choice for busy establishments where speed is crucial. Operators can load pizzas into both decks simultaneously, significantly reducing cooking times during peak hours.

Another key characteristic of the PS300F is its digital control panel. This user-friendly interface allows operators to set precise cooking times and temperatures, ensuring optimal results every time. The oven also features programmable settings, enabling users to save specific cooking parameters for different types of pizzas, simplifying the process during high-volume service.

Energy efficiency is another important consideration in the design of the PS300F. The oven is constructed with high-quality insulation to minimize heat loss, contributing to lower energy consumption. This makes it not only an environmentally friendly option but also a cost-effective choice for businesses looking to reduce their utility bills.

Durability is a hallmark of the Middleby Marshall brand, and the PS300F exemplifies this commitment to quality. Built with robust materials and designed to withstand the rigors of a busy kitchen, this oven promises longevity and reliable performance.

In conclusion, the Middleby Marshall PS300F is a top-tier pizza oven that brings together innovative technology, efficiency, and durability. Its advanced features make it an excellent investment for any foodservice operation focused on delivering high-quality pizzas in a fast-paced environment. With its combination of performance and ease of use, the PS300F is poised to enhance any culinary experience.
Top Page Image Contents