Manuals / Miele / Kitchen Appliance / Ventilation Hood

Miele M.-Nr. 09 805 980 installation instructions Installation

Models: M.-Nr. 09 805 980

1 56

Download 56 pages 20.7 Kb

Page 38

Image 38

Installation

Hang the installation frame on the four screws. The front of the frame is marked with a "V."

If using the spacer frame, place the two covers into the fixing holes.

Align the installation frame and se‐ cure it with the screws.

The spacers, which were removed from the spacer frame at the start, can be used to align the hood verti‐ cally.

Page 38

Image 38

Miele M.-Nr. 09 805 980 installation instructions Installation

Contents

en-US M.-Nr.09 805Contents Contents IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Technical safetyChildren IMPORTANT SAFETY INSTRUCTIONS Be certain your appliance is properly installed and grounded by a qualified technician. To guarantee the electrical safety of this appli‐ ance, continuity must exist between the appliance and an effective grounding system. It is imperative that this basic safety requirement be met. If there is any doubt, have the electrical system of the house checked by a qualified electricianProper use IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS –b NEVER PICK UP A FLAMING PAN - You may be burnedIMPORTANT SAFETY INSTRUCTIONS Overheated oils and fats can ignite and set the ventilation hood on fireProper installation IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS Be sure to observe the information contained in the Installation section when mounting the ventilation hoodFCC Declaration of Conformity Cleaning and careAccessories FCC Radiation Exposure StatementDisposal of your old appliance Caring for the environmentDisposal of the packing mate‐ rial Description of functions Vented modeRecirculation mode Non-returnflapCon@ctivity 2.0 function Description of functionsGuide to the appliance Guide to the appliance aChimney extension b Chimney c CanopyReaction time Operation Automatic modeCooking with Con@ctivity 2.0 Automatic mode Operation Automatic mode Cooking processTurning off Operation Automatic mode Temporarily exiting Automatic modeResuming Automatic mode Selecting the delayed shut down time Operation Manual modeSelecting the power level Turning on the fanOperation Manual mode Power managementTurning overhead lighting on/off Turning power management on/offFilter saturation indicator Operation Automatic and Manual modesOperation Automatic and Manual modes Checking the filter saturation indica‐ torSensor button signal tone Operation Automatic and Manual modesSpecial instructions for RAL color finish housing Cleaning and careStainless steel housing GeneralCleaning intervals Grease filtersCleaning and care Special instructions for control but‐ tonsUnsuitable cleaning agents Cleaning and careCleaning the grease filters by hand Cleaning the grease filters in the dishwasherInstalling/replacing the OdorFree Charcoal Filter OdorFree Charcoal FilterCleaning and care Disposing of the OdorFree Charcoal Filter Cleaning and careWhen to change the OdorFree Char‐ coal Filter Installation parts InstallationBefore installation DUI 32 recirculation kit for recircula‐ tion modeAppliance dimensions InstallationDistance between cooktop and ventilation hood S InstallationRemoving the protective film Installation recommendationsStructural support InstallationInstallation Installation Use a knife to release the four spacers and the two covers from the spacer frame suppliedInstallation The spacer frame can be installed be‐ tween the chimney and the ceiling. This creates a shadow which gives the illu‐ sion of a gap between the ceiling and the chimney. This is useful if the ceiling is not level or is uneven. The hood is aligned vertically with the spacers sup‐ plied. Visual irregularities between the chimney and the ceiling are then con‐ cealed by the shadowInstallation Hang the installation frame on the four screws. The front of the frame is marked with aInstallation Replace the screwsInstallation  Check that the hose is held securelyInstallation Bend back the two retaining tabsInstallation Secure the hood with the screws suppliedInstallation  Connect the power cord. See Elec‐Installation Raise the canopy to the desired height and secure it with the screwsfrom the grease filters InstallationRemove the grease filters from the hood  Reinsert the grease filtersExhaust duct Condensate trap Exhaust ductElectrical connection Grounding InstructionsActivating the Con@ctivity 2.0 function Installation of the Con@ctivity 2.0 stickActivating Con@ctivity Activating the ventilation hoodActivating the cooktop Deactivating Con@ctivityActivating Con@ctivity Activation failedLocation of the data plate Service and warrantyWarranty Technical data Page Page Technical Service & Support Nationwide U.S.ACanada Miele, IncM.-Nr.09 805 980 / DA 6690 Den-US