Manuals / Miele / Kitchen Appliance / Ventilation Hood

Miele M.-Nr. 09 805 980 installation instructions Installation

Models: M.-Nr. 09 805 980

1 56

Download 56 pages 20.7 Kb

Page 44

Image 44

Installation

Raise the canopy to the desired height and secure it with the screws.

Hold the chimney securely, bend back the retaining tabs and carefully lower it.

The chimney will locate in the cut-out in the canopy.

Page 44

Image 44

Miele M.-Nr. 09 805 980 Installation, Raise the canopy to the desired height and secure it with the screws

Contents

en-US M.-Nr.09 805Contents Contents IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Technical safetyChildren IMPORTANT SAFETY INSTRUCTIONS Be certain your appliance is properly installed and grounded by a qualified technician. To guarantee the electrical safety of this appli‐ ance, continuity must exist between the appliance and an effective grounding system. It is imperative that this basic safety requirement be met. If there is any doubt, have the electrical system of the house checked by a qualified electricianProper use IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS –b NEVER PICK UP A FLAMING PAN - You may be burnedIMPORTANT SAFETY INSTRUCTIONS Overheated oils and fats can ignite and set the ventilation hood on fireProper installation IMPORTANT SAFETY INSTRUCTIONSIMPORTANT SAFETY INSTRUCTIONS Be sure to observe the information contained in the Installation section when mounting the ventilation hoodCleaning and care AccessoriesFCC Declaration of Conformity FCC Radiation Exposure StatementDisposal of your old appliance Caring for the environmentDisposal of the packing mate‐ rial Vented mode Recirculation modeDescription of functions Non-returnflapCon@ctivity 2.0 function Description of functionsGuide to the appliance Guide to the appliance aChimney extension b Chimney c CanopyReaction time Operation Automatic modeCooking with Con@ctivity 2.0 Automatic mode Operation Automatic mode Cooking processTurning off Operation Automatic mode Temporarily exiting Automatic modeResuming Automatic mode Operation Manual mode Selecting the power levelSelecting the delayed shut down time Turning on the fanPower management Turning overhead lighting on/offOperation Manual mode Turning power management on/offFilter saturation indicator Operation Automatic and Manual modesOperation Automatic and Manual modes Checking the filter saturation indica‐ torSensor button signal tone Operation Automatic and Manual modesCleaning and care Stainless steel housingSpecial instructions for RAL color finish housing GeneralGrease filters Cleaning and careCleaning intervals Special instructions for control but‐ tonsCleaning and care Cleaning the grease filters by handUnsuitable cleaning agents Cleaning the grease filters in the dishwasherInstalling/replacing the OdorFree Charcoal Filter OdorFree Charcoal FilterCleaning and care Disposing of the OdorFree Charcoal Filter Cleaning and careWhen to change the OdorFree Char‐ coal Filter Installation Before installationInstallation parts DUI 32 recirculation kit for recircula‐ tion modeAppliance dimensions InstallationDistance between cooktop and ventilation hood S InstallationInstallation recommendations Structural supportRemoving the protective film InstallationInstallation Installation Use a knife to release the four spacers and the two covers from the spacer frame suppliedInstallation The spacer frame can be installed be‐ tween the chimney and the ceiling. This creates a shadow which gives the illu‐ sion of a gap between the ceiling and the chimney. This is useful if the ceiling is not level or is uneven. The hood is aligned vertically with the spacers sup‐ plied. Visual irregularities between the chimney and the ceiling are then con‐ cealed by the shadowInstallation Hang the installation frame on the four screws. The front of the frame is marked with aInstallation Replace the screwsInstallation  Check that the hose is held securelyInstallation Bend back the two retaining tabsInstallation Secure the hood with the screws suppliedInstallation  Connect the power cord. See Elec‐Installation Raise the canopy to the desired height and secure it with the screwsInstallation Remove the grease filters from the hoodfrom the grease filters  Reinsert the grease filtersExhaust duct Condensate trap Exhaust ductElectrical connection Grounding InstructionsInstallation of the Con@ctivity 2.0 stick Activating Con@ctivityActivating the Con@ctivity 2.0 function Activating the ventilation hoodDeactivating Con@ctivity Activating Con@ctivityActivating the cooktop Activation failedLocation of the data plate Service and warrantyWarranty Technical data Page Page U.S.A CanadaTechnical Service & Support Nationwide Miele, IncM.-Nr.09 805 980 / DA 6690 Den-US