Extending cooldown time | Miele T 7644 C guide

Programmable functions

Extending cooldown time

You can individually lengthen the cooldown phase the occurs before the end of a program. Fabrics will be more completely cooled down.

Cooldown time

–can be extended by two stages.

–it does not function for Smoothing programme.

For programming and saving in memory, follow steps to .

The programmable function is programmed using the buttons.

Precondition:

–The dryer is switched off.

–The door is closed.

Press Start/Stop and keep it pressed it during steps -.

Press the I-On/0-Offbutton in.

Wait until the Start/Stop button lights up continuously . . .

. . . then release the Start/Stop button.

Press the Gentle button three times.

–The Gentle indicator light flashes briefly seven times.

–P and 0 flash alternatingly in the display (default setting).

The number appearing alternatingly with P means:

0Default setting

IFive minutes longer cooldown time (Express indicator light will flash once)

2Ten minutes longer cooldown time (Express indicator light will also flash twice)

Pressing the Start/Stop button switches from one to the other.

Using the I-On/0-Offbutton, switch the dryer off.

The programming is now stored in memory. You can change it again at any time.

49

Image 49

Miele T 7644 C operating instructions Extending cooldown time

Contents

Operating Instructions For condenser tumble dryer T 7644 C Disposal of packing material Caring for the environmentDisposing of your old appliance Saving energy Contents Contents Important Safety Instructions Grounding Instructions This dryer is intended for residential use only Accessories Description Main FeaturesOperating the dryer Dear Customer Function of Miele condenser dryer Laundry care anti-crease action and roll-up prevention To do all this, the dryer is equipped with systems Operating the dryer Fault indicator / Optical interfaceControl panel Display Program duration/ Estimated time remaining DelayProgrammable functions Laundry care Care symbolsDrying tips Drying Laundry care Brief instructions Proper dryingPreparing the laundry Turn on the dryer Select program Extra options/Select DelayDryness level selection in programs Before the end of a program Starting the programEnd of program Remove laundry Delay Options/DelayGentle Buzzer Normal Extra dry, Normal Program OverviewHand iron, Rotary iron Wrinkle-free Extra dry, Normal, Hand iron Smoothing WoolensExpress Normal, Hand iron Dress shirts Normal, Hand iron Timed warm Timed cold Changing the program sequence Switching over from a running programLoading or removing laundry Time remaining Activating the lock Electronic lockDeactivating the lock Emptying the condensed water container Cleaning and care Cleaning without water Cleaning the lint filtration components Cleaning with water Cleaning the dryer Removing the condenser unit Cleaning the condenser heat exchanger unit Checking the condenser unit Handle of the unit must be on top, the locking lever down Replacing the condenser unit Test and fault messages Trouble shootingWhat to do, if . . . ? Canceling test Problem Cause SolutionCanceling the fault Container indicator light Other problems Cleaned Problem Cause Solution Water runs fromDryer after Condenser has been When switched on Start and the indicatorCold programs will not Lights for these programs Replacing the light bulb Program updates Customer serviceWarranty conditions and warranty period Optional accessories Front view Installation and connection Carrying the dryer to the installation site Rear view Installation siteWasher-dryer stack Leveling the dryer Before transport at a later date Ventilating the installation area General Draining condensed water externallyArranging the drain hose Hooking up the drain hose in sink or floor drain Special installation conditions requiring a non-return valve Installation and connection Electrical connections Technical data Programmable functions for changing Standard values Extending the range of drying levels Programmable functions Buzzer normal default setting Buzzer loud Adjusting buzzer volumeFor programming and saving in memory, follow steps to Set memory function No Memory default settingMemory Extending cooldown time Change function of Filter/Vent indication Default setting No Keypad tone default setting Keypad tone on Adjust keypad tone Default setting Lower conductivity setting Changing water conductivity settingImportant condition Page Page Page Alteration rights reserved Nr 323 260