Set memory function, Memory | Miele T 7644 C specs

Programmable functions

Set memory function

The electronics memorizes any selected program with extra options. The duration of a Smoothing program will also be stored in memory.

These settings will be used for the next drying. They can be accepted, or changed by using the buttons.

For programming and saving in memory, follow steps to .

The programmable function is programmed using the buttons.

Precondition:

–The dryer is switched off.

–The door is closed.

Press Start/Stop and keep it pressed it during steps -.

Press the I-On/0-Offbutton in.

Wait until the Start/Stop button lights up continuously . . .

. . . then release the Start/Stop button.

Press the Gentle button twice.

–The Gentle indicator light flashes briefly six times.

–P and 0 flash alternatingly in the display (default setting).

The number appearing alternatingly with P means:

IMemory

(Express indicator light also flashes)

0no Memory (default setting)

Pressing the Start/Stop button switches from one to the other.

Using the I-On/0-Offbutton, switch the dryer off.

The programming is now stored in memory. You can change it again at any time.

48

Image 48

Miele T 7644 C operating instructions Set memory function, No Memory default setting

Contents

Operating Instructions For condenser tumble dryer T 7644 C Caring for the environment Disposal of packing materialDisposing of your old appliance Saving energy Contents Contents Important Safety Instructions This dryer is intended for residential use only Grounding Instructions Accessories Main Features DescriptionOperating the dryer Dear Customer Function of Miele condenser dryer To do all this, the dryer is equipped with systems Laundry care anti-crease action and roll-up prevention Fault indicator / Optical interface Operating the dryerControl panel Display Delay Program duration/ Estimated time remainingProgrammable functions Care symbols Laundry careDrying tips Drying Laundry care Proper drying Brief instructionsPreparing the laundry Turn on the dryer Extra options/Select Delay Select programDryness level selection in programs Starting the program Before the end of a programEnd of program Remove laundry Options/Delay DelayGentle Buzzer Program Overview Normal Extra dry, NormalHand iron, Rotary iron Wrinkle-free Extra dry, Normal, Hand iron Woolens SmoothingExpress Normal, Hand iron Dress shirts Normal, Hand iron Timed cold Timed warm Switching over from a running program Changing the program sequenceLoading or removing laundry Time remaining Electronic lock Activating the lockDeactivating the lock Cleaning and care Emptying the condensed water container Cleaning the lint filtration components Cleaning without water Cleaning the dryer Cleaning with water Cleaning the condenser heat exchanger unit Removing the condenser unit Checking the condenser unit Replacing the condenser unit Handle of the unit must be on top, the locking lever down Trouble shooting Test and fault messagesWhat to do, if . . . ? Problem Cause Solution Canceling testCanceling the fault Container indicator light Other problems Problem Cause Solution Water runs from CleanedDryer after Condenser has been Start and the indicator When switched onCold programs will not Lights for these programs Replacing the light bulb Customer service Program updatesWarranty conditions and warranty period Optional accessories Installation and connection Front view Rear view Installation site Carrying the dryer to the installation siteWasher-dryer stack Leveling the dryer Ventilating the installation area Before transport at a later date Draining condensed water externally GeneralArranging the drain hose Special installation conditions requiring a non-return valve Hooking up the drain hose in sink or floor drain Installation and connection Electrical connections Technical data Programmable functions for changing Standard values Programmable functions Extending the range of drying levels Adjusting buzzer volume Buzzer normal default setting Buzzer loudFor programming and saving in memory, follow steps to No Memory default setting Set memory functionMemory Extending cooldown time Default setting Change function of Filter/Vent indication Adjust keypad tone No Keypad tone default setting Keypad tone on Changing water conductivity setting Default setting Lower conductivity settingImportant condition Page Page Page Alteration rights reserved Nr 323 260