Installing Exhaust Pipe, Fuel, Oil | Miller Electric Miller DU-OP

5-4. Installing Exhaust Pipe

Tools Needed: 1/2 in

5-5. Engine Prestart Checks

1/2 in
(13 mm)	Full
	Full
	Diesel

Valve Open

I

O

YStop engine and let cool.

YDo not blow exhaust toward air cleaner or air intake.

Top View

exh_pipe2 4/96 − 154 089-A / 154 611 / 190 377

Check all fluids daily. Engine must be cold and on a level surface.

Follow run-in procedure in engine manual. If unburned fuel and oil col- lect in exhaust pipe during run-in, see Section 10.

Fuel

YDo not use gasoline. Gaso- line will damage engine.

Add diesel fuel before starting engine the first time (see mainte- nance label for specifications). Fill fuel tank up to 1/2 in. (13 mm) from top to allow room for expansion. Open fuel shut-off valve.

Do not run out of fuel or air enters fuel system and causes starting problems. See engine manual to bleed air from fuel system.

Oil

After fueling, check oil with unit on level surface. If oil is not up to full mark on dipstick, add oil (see main- tenance label).

.Engine stops if oil pressure is too low.

.To improve cold weather starting:

Keep battery in good condition. Store battery in warm area.

Use fuel formulated for cold

weather (diesel fuel can gel in cold weather). Contact local fuel supplier for fuel in- formation.

Full	Use correct grade oil for cold
	weather.
	Ref. 158 633-C / S-176 697

OM-494 Page 16

Image 20

Miller Electric Miller DU-OP manual Installing Exhaust Pipe, Engine Prestart Checks, Stop engine and let cool, Fuel, Oil

Contents

Processes DescriptionFile Engine Drive Visit our website at OM-494191 862Q September From Miller to You Table of Contents − Operating Auxiliary Equipment Symbol Usage Arc Welding Hazards Engine Hazards Compressed Air Hazards Principal Safety Standards California Proposition 65 WarningsEMF Information Radiation can cause interference Signification des symboles − Consignes DE Sécurité − Lire Avant UtilisationUN Choc Électrique peut tuer LES Fumées ET LES GAZ peuvent être dangereux LE Soudage peut provoquer un in- cendie ou une explosion DES Particules Volantes peuvent blesser les yeuxDES Pièces Chaudes peuvent provoquer des brûlures graves LE Bruit peut affecter l’ouïe LA Chaleur DU Moteur peut pro- voquer un incendie ’AIR Comprimé peut provoquer des blessures’EMPLOI Excessif peut LE Surchauffement peut endom- mager le moteur électrique LE Soudage À L’ARC risque de provoquer des interférences Pour les moteurs à essencePour les moteurs diesel Boulevard, Rexdale, Ontario, Canada M9W 1R3 téléphone Symbols And Definitions − Definitions − Specifications Weld, Power, And Engine SpecificationsDimensions, Weights, And Operating Angles Description AC Generator Power Fuel Consumption Exceeding duty cycle can damage unit and void warranty Duty Cycle And OverheatingOverheating Reduce Duty Cycle Minutes CC/DC − Single Mode CC/DC − Dual ModeCV/DC Mode Volt-Ampere Curves − Installation Installing Welding Generator Activating The Dry Charge Battery If Applicable Connecting The BatteryDo not overfill battery cells For 30 Minutes Installing Exhaust Pipe Engine Prestart ChecksStop engine and let cool Fuel Safety Information For Connecting To Weld Output Terminals Weld Output TerminalsUnexpected Weld Output can cause injury or fire Welder a Left Side Welder B Right Side Welder a Left Side Do not exceed machine duty cycle Stop engine Do not exceed machine duty cycle Connect electrode holder cables to Elec- trode receptacles Place optional Polarity switches in Re Verse position when using CV weld reWhen switch is in Straight position Switches are set correctly. See Section Connect wire feeder cables to Negative − terminals Connect wire feeder cables to CV recep- tacles Be sure Process Selector switches are Place optional Polarity switch in Re Making Single Operator CC Weld Connections OM-494 Selecting Weld Cable Sizes 150 ft 200 ft 250 ft350 ft 400 ft 45 m 60 m 70 m 90 m 105 m 120 m Put terminals Installing Ether Cylinder Optional Ether Starting Aid After installing cylinder, wait atRemote 14 Receptacle Information Socket Information Remote 14 Receptacle Connections Dual Operator Operation − Operating the Welding Generator Engine ControlsSee -3for weld control descriptions If light goes on, stop engine and check engine belt Weld Controls See Section Do not switch under load or with out- put on Do not switch under loadWeld Control Descriptions See Section CV weld output for MIG is only available Generator power is not affected by weld output − Operating Auxiliary EquipmentVolt And 240 Volt Duplex Receptacles At least once a month, run engine at − Maintenance & Troubleshooting Routine Maintenance Maintenance Label Servicing Air Cleaner By the warrantyTo clean air filter Do not clean housing with air hose Servicing Fuel And Lubrication Systems Adjusting Engine Speed Weld/PowerServicing Optional Ether Starting Aid Cylinder To adjust belt tension Checking And Replacing Alternator BeltMax Tools Needed 11/16 Stop engine To check belt tension Resetting Fan Belt Safety Shutdown Checking Generator Brushes Inspecting And Cleaning Optional Spark Arrestor MufflerStop engine and let cool. Reinstall cleanout plug Circuit Protection Thermostats TP3 And TP4 Internal − Not Shown Troubleshooting Welding Factory Authorized Service Agent check main rectifier SR2 Factory Authorized Service Agent check main rectifier SR3Repair or replace wire feeder Formers T5 thru T10, and control board PC1 or PC5 Generator Power Engine OM-494 − Electrical Diagrams Circuit Diagram For Welding Generator 210 657-A Ment damage may occur − RUN-IN ProcedureWetstacking Run-In Procedure Using Load Bank 4exceed duty cycle or equip- ment damage may occurCheck oil level frequently dur Ing run-in add oil if needed Run-In Procedure Using Resistance Grid Procedure at less thanBank/grid From flammables − Generator Power Guidelines Has this symbolSelecting Equipment Grounding Generator To Truck Or Trailer Frame Grounding When Supplying Building Systems How Much Power Does Equipment Require?Earth ground if supplying Use ground device as stated Electrical codes Approximate Power Requirements For Industrial Motors Approximate Power Requirements For Farm/Home EquipmentIndustrial Motors Rating Starting Watts Running Watts Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Power Required To Start Motor How Much Power Can Generator Supply?Single-Phase Induction Motor Starting Requirements KVA/HP x HP x 1000 = Starting Amperage Typical Connections To Supply Standby Power Selecting Extension Cord Use Shortest Cord Possible Current Load Watts Amperes − Parts List 96−SEE FIG 92 91 103 102 101 100 25−SEE FIG 910 4748 57−SEE FIG 78−SEE FIG 76 75 Item Dia Part Description Quantity Mkgs 189 Front Panel Front Panel -1Item Side Control Panels − Welder B Right Side Shown Side Control Panels -1Item Side Control Panels Generator Rectifier Assembly OM-494 Page Support ServiceYour distributor also gives To locate a Distributor or Service Agency visit Miller Electric Mfg. CoFor assistance in filing or settling claims, contact Your distributor and/or equipment manufacturer’s