Milwaukee 4125, 58-14-3005d9, 4092-20 15A, 4120, 4094 20A, 4090 15A, 4097-20 15A, 4096 20A Accessories

ACCESSORIES

WARNING!

To reduce the risk of injury, always unplug the tool before attaching or removing accessories. Use only specifically recommended acces- sories. Others may be hazardous.

For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go on-line to www.milwaukeetool.com. To obtain a catalog, contact your local distributor or a service center.

Meter Boxes

Cat. No. 48-51-0100 (30 amp, 120 volt) (Not available in Canada)

Same as supplied with Vac-U-Rig®Attachment Kit No. 49-22-7075 and with Cat. No. 4136. Ammeter and power switch appear on the front panel and a single 20 amp twist lock receptacle for the drill motor and two convenience outlets are on the back of the box.

Meter Boxes

Cat. No. 48-51-0120 (20 amp, 120 volt) (Can be used in Canada)

Ammeter and power switch appear on the front panel with a single 20 amp twist lock receptacle for the drill motor on the back.

Telescoping Extension Assembly

Cat. No. 49-95-1000

This assembly braces the rig between the floor and ceiling for maximum rigidity. It adjusts for 14-foot ceilings and features fixed hole adjust- ments.

Copper Washer

Cat. No. 45-88-8565

Before using the tool, slip this washer onto the spindle to prevent the bit from seizing on spindle during coring.

Spacer Assembly

Cat. No. 49-67-0110

For use with Cat. Nos. 4125 and 4130. Mounts between cradle and Dymodrill motor when using 10" - 14" coring bits.

Spacer Assembly

Cat. No. 49-67-0115

For use with Cat. No. 4115 and 4120. Mounts between cradle and Dymodrill motor when using 10" - 14" coring bits.

Water Collecting Ring

Cat. No. 48-70-0060

For use where water flow from coring must be trapped and drained. Dike-type collector ring holds water for fast disposal when used with bits up to 10" in diameter. A built-in vacuum hose fitting also allows the ring to be used with a wet/dry vacuum cleaner.

Water Hose

Cat. No. 49-18-0055

This 8-foot water hose features a 5/8" coupling and standard brass male and female water hose fittings.

Water Tank

Cat. No. 49-76-0055

This 3-1/2 gallon heavy-duty, impact-resistant poly tank is for use where a regular tap water supply is not available.

Vacuum Pad Assembly (Single Pad)

Cat. No. 49-22-7100

This single vacuum pad is the same as supplied with Vac-U-Rig®Attach- ment Kit No. 49-22-7075. Can be used with Cat. Nos. 4115, 4125 and 4130.

Vacuum Pump Assembly (115 Volts)

Cat. No. 49-50-0160

This heavy-duty 1/8 H.P. pump comes complete with vacuum gauge, air filter and cord. May be mounted to the base of the unit. Same as fur- nished with Vac-U-Rig®49-22-7075. Can be used with Cat. Nos. 4115, 4125 and 4130.

Vacuum Pump Assembly (115 Volts)

Cat. No. 49-50-0165

This heavy-duty 1/8 H.P. pump comes complete with vacuum gauge, air filter and cord. May be mounted to the base of the unit. Can be used with Cat. No. 4120.

Vac-U-Rig® Attachment Kit (115 Volts)

Cat. No. 49-22-7065

This kit includes: (1) vacuum pad; (1) vacuum pump assembly with gauge, filter, 8-foot air hose, and fittings. Can be used with Cat. No. 4120.

Vac-U-Rig® Attachment Kit

Cat. No. 49-22-7075

This kit includes: (1) vacuum pad; (1) vacuum pump assembly with gauge, filter, 8-foot air hose, and fittings. Can be used with Cat. Nos. 4115, 4125 & 4130.

Threaded Adapter

Cat. No. 48-04-0160

Thread Adapter reduces the thread size of 1-1/4"-7 to 5/8"-11 MILWAUKEE Dymobits and extensions.

Shear Pin No. 44-60-0065 (Low Strength Shear Pin) Shear Pin No. 44-60-0032* (High Strength Shear Pin)

*(Standard equipment on Dymodrills except clutch Cat. Nos. 4004, 4005, 4092, 4206 and 4097).

9" Bit Extension

Cat. No. 48-95-1500

Extension threaded on both ends with a 1-1/4"-7 thread. For use with Diamond Core Bits over 2" in diameter and a 1-1/4"-7 thread. Extension mounts directly to the Dymodrill. Two or more extensions can be used together to core deep holes.

10-1/2" Bit Extension

Cat. No. 48-95-2100

Extension threaded on both ends with a 5/8"-11 thread. For use with 1-1/4" and 1-1/2" diameter Diamond Core Bits with a 5/8"-11 thread. Extension requires Threaded Adapter No. 48-04-0160 for mounting to Dymodrills. Two or more extensions can be used together to core deep holes.

3/16" Socket Wrench

Cat. No. 49-96-0085

Use to mount Dymodrills onto the cradle on Dymorigs

1-3/8" Open End Wrench

Cat. No. 49-96-4700

Use to install bits onto Dymodrills.

Vacuum Pad Gasket

Cat. No. 43-44-0570

Replacement part for vacuum pads on Cat. Nos. 4115, 4125 & 4130

Vacuum Base Gasket

Cat. No. 43-44-0605

Replacement part for vacuum base Cat. No. 4120.

Rubber Cement

Cat. No. 44-22-0060

Use to bond vacuum pad gaskets to vacuum pads on Cat. Nos. 4115, 4120, 4125 and 4130.

Type "E" Grease

Cat. No. 49-08-4122

Use for lubricating rack and pinion as well as spindle.

page 14