Adding channels to the TVÕs memory | Mintek 27HL85 guide

Adding channels to the TVÕs memory

When you press Channel y or z, your TV will stop only on the channels you program into the TVÕs channel memory.

Follow the steps below and on the next page to program all active channels into the TVÕs memory.

Programming channels automatically

Your TV can automatically detect all active channels in your area and store them in the channel memory. After the channels are

Note:

To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.

TV/VIDEO RECALL POWER

INFO

programmed automatically, you can manually add or erase individual channels (see page 30).

To program channels automatically:

1.	Press MENU, and then press x or • until the SET UP menu
	appears.
2.	Press y or z to highlight TV/CABLE.

1

4

7

+10

100

			NU
			E
		P	M	ORITE
T	O	P		ORITE
	O
			FAV
			FAV

2

5

8

0

FAV

3

6

9

CHRTN

ENT

		G
		UI
	PIC	D
	PIC	E
		E
	SIZE

Setting up your TV

3. Press x or • to select either TV or CABLE, depending on which

you use. If you use an antenna, select TV; if you use cable

channels, select CABLE.

SET UP	1/2

LANGUAGE	ENGLISH

TV/CABLE	CABLE

CH PROGRAM	ENTER

ADD/ERASE	ADD

CH LABELING	ENTER
VIDEO LABEL

MENU BACK EXIT WATCH TV

4. Press z to select CH PROGRAM.

SET UP	1/2
LANGUAGE	ENGLISH
TV/CABLE	CABLE
CH PROGRAM	ENTER
ADD/ERASE	ADD
CH LABELING	ENTER
VIDEO LABEL

MENU BACK EXIT WATCH TV

5.Press ENTER to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory.

While the TV is cycling through the channels, the message ÒProgramming NowÑPlease WaitÓ appears.

6.When channel programming is complete, the message ÒCompletedÓ appears.

7.Press Channel y or z to view the programmed channels.

MENU

DVDMENU

	ENTER			EXIT		R
N				EXIT		R
E
T		FAV			A
	E	FAV			A
	R			LE
	R			C
TV		CH	VOL
CBL/SAT		CH	VOL
VCR
DVD
	POP DIRECT CH MUTE			SLEEP
TV/VCR		PAUSE	STOP	PLAY
		FREEZE	SOURCE	SPLIT
REW		FF	SKIP/SEARCH
CH SCAN		SWAP	POP CH
	REC			LIGHT

MENU

yzx •

ENTER Channel yz

24

Image 24

Mintek 27HL85 owner manual Adding channels to the TVÕs memory, Programming channels automatically

Contents

27HL85 Safety Precautions Dear Customer Important Safety Instructions Installation Service Care cont. from previous column Important notes about your LCD TV Introduction Supplied accessories Check that you have the accessories and items shownIntroduction Welcome to Toshiba Exploring your new TV Video Connecting your TV Connecting an antenna or cable TVChannels Connecting a VCR Connecting a cable converter box and VCR Connecting a DVD player or satellite receiver and a VCR Introduction Connecting yourTV DVD player with component video For Hdmi or DVI connection, see Connecting two VCRs Connecting a camcorder Connecting an HDMIª or a DVI device to the Hdmi input ¥ one Hdmi cable type a connector¥ one HDMIÐtoÐDVI adapter cable Hdmi type a connector ¥ one pair of standard analog audio cables Using the remote control Preparing the remote control for useInstalling the remote control batteries Remote control effective range Remote control codes For future reference, write down the codes you used Remote control codes Introduction Connecting YourTV Control Remote Control function key chart CLEAR/EXIT Learning about the remote control Connecting YourTV Control Setting up your TV Learning about the menu system Changing the on-screen display language Press x or to highlight your desired language Adding channels to the TVÕs memory Programming channels automatically Changing channels Adding and erasing channels manually Using the TVÕs features Adjusting the channel settingsSwitching between two channels using Channel Return Programming your favorite channels Connecting Labeling channels Viewing the wide-screen picture formats Selecting the picture size Theaterwide 1 picture size For 43 format programs Adjusting the Picture SIZE/POSITION Using the Auto Aspect feature Press y or z to highlight Auto AspectPress x or to select on Using the Gray screen function Selecting the gray level of the side panels Using the Locks menu Using the V-CHIP menuEntering the PIN code If you cannot remember your PIN code OFF To release your setting Unlock TV Rating Independent rating system for broadcastersTV Rating menu appears Press z or y to select an item Repeat steps 2 and 3 to set the next item Mpaa Rating Independent rating system for movies Chip menu Locking channels Unlocking programs temporarilyRepeat steps 2 and 3 for other channels Repeat for other channels Locking the video inputs Changing the PIN code Adjusting the picture Selecting the picture modeAdjusting the back light feature Press x or to select the mode you prefer Adjusting the picture quality Using the Black stretch feature Using the Mpeg NR feature Using the CableClear¨ DNR featurePress x or to select HIGH, MIDDLE, LOW, or OFF Selecting the color temperature Selecting the cinema mode Selecting the video input source Labeling the video input sources Using the closed caption feature Press x or to highlight C1-C4 or T1-T4¥ To view text, highlight T1, T2, T3, or T4 Setting the sleep timer Setting the on timer Adjusting the sound Muting the soundSelecting stereo/SAP broadcasts Using the WOWª surround sound feature Adjusting the sound quality Using the StableSound¨ featureTo turn off the StableSound feature Select OFF in above Understanding the auto power off feature Understanding the last mode memory featureDisplaying on-screen information Specifications Appendix Troubleshooting AntennaBlack box appears on the screen T2, T3, or T4. Turn closed captioning OFF Limited United States Warranty Limited Canada Warranty Index Channel programming Toshiba ELECTROMEX, S.A. DE C.V