Unlocking programs temporarily

1.If you try to watch a TV program that exceeds the rating limits you set, the TV enters program lock mode. You can either unlock the program temporarily (see steps 2Ð4 below) or select an unlocked program to watch.

THIS PROGRAM HAS BEEN BLOCKED!

TV –Y

EXCEEDS SET LIMITS

PUSH MUTE TO ENTER PIN

2.To temporarily unlock the program, press MUTE while the message is on the screen.

3.Press the Number buttons (0Ð9) to enter your 4-digit PIN code.

PIN CODE

BLOCKING ACTIVE

ENTER PIN CODE

TO TEMPORARILY UN–BLOCK

 

 

 

 

 

 

 

 

0 - 9 SELECT

 

ENTER SET

MENU BACK

 

EXIT

 

WATCH TV

4.Press ENTER.

If the correct code is entered, the program lock mode is released and the normal picture appears.

All locking is disabled until the TV is turned off, and will be enabled when the TV is turned on again.

Locking channels

With the CH LOCK feature, you can lock specific channels. You will not be able to tune locked channels with the Channel y z buttons or Channel Number buttons unless you clear the setting.

You can lock a maximum of nine channels. To lock channels:

1.From the LOCKS menu, press y or z to highlight CH LOCK, and then press ENTER.

The CH LOCK menu appears, and CH INPUT will be highlighted.

2.Press the Channel Number buttons to enter the channel you want to lock.

 

 

 

TV/VIDEO RECALL

POWER

 

 

 

 

 

 

 

INFO

 

 

 

 

 

 

 

 

 

1

2

 

 

3

 

 

 

 

 

 

 

4

5

 

 

6

 

 

Channel

 

 

 

 

7

8

 

 

9

 

 

 

 

 

 

 

 

 

 

Number

 

 

 

 

+10

 

CHRTN

 

 

 

 

 

100

0

 

 

ENT

 

 

 

 

 

 

NU

 

 

 

G

 

 

 

 

 

 

E

 

FAV

 

 

UI

 

 

 

P

M

 

 

 

PIC

D

 

 

O

FAVORITE

 

 

 

 

E

T

 

 

 

 

 

 

SI

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZE

 

 

 

 

 

 

 

MENU

 

 

 

 

 

 

 

 

 

 

DVDMENU

 

 

 

yzx •

 

 

 

 

 

 

 

 

 

 

 

E ENTE

 

 

 

EXIT

 

R

N

 

R

 

 

 

A

 

T

FAV

 

 

 

 

 

 

 

E

 

 

 

 

 

 

 

 

 

R

 

 

 

 

 

LE

ENTER

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

TV

 

CH

 

VOL

 

 

 

 

 

CBL/SAT

 

 

 

 

 

 

VCR

 

 

 

 

 

 

 

 

 

DVD

 

 

 

 

 

 

 

 

 

 

 

 

POP DIRECT CH MUTE

SLEEP

 

TV/VCR

PAUSE

STOP

PLAY

MUTE

 

 

 

 

 

 

FREEZE SOURCE

SPLIT

 

 

 

REW

FF

SKIP/SEARCH

 

 

CH SCAN

SWAP

 

POP CH

 

 

 

 

 

REC

 

 

 

LIGHT

 

LOCKS menu

 

LOCKS

V-CHIP

ENTER

E

F

S

Introduction

Connecting

yourTV

 

 

 

 

Usingthe

remotecontrol

 

 

 

 

Settingup

yourTV

 

 

TVÕs

 

3. Press ENTER.

 

 

 

 

CH LOCK

 

 

 

 

 

 

 

 

 

 

 

CH INPUT

 

 

 

1 2

 

 

 

 

 

 

 

 

 

 

 

 

- - -

- - -

- - -

 

 

- - -

 

 

 

- - -

 

- - -

- - -

- - -

 

 

- - -

 

- - -

- - -

- - -

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TV

CABLE

CLEAR ALL

 

 

 

ENTER

 

 

 

 

 

 

 

 

 

 

0 - 9 SELECT

ENTER SET

 

MENU BACK

 

EXIT WATCH TV

 

 

 

 

CH LOCK

 

 

CH INPUT

 

 

 

 

 

 

 

 

- - -

 

 

 

 

 

 

 

 

 

 

 

 

- - -

- - -

- - -

 

 

1 2

 

 

 

- - -

 

- - -

- - -

- - -

 

 

- - -

 

- - -

- - -

- - -

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TV

CABLE

 

CLEAR ALL

 

 

 

ENTER

 

 

0 - 9 SELECT

ENTER SET

 

 

MENU BACK

 

EXIT WATCH TV

 

CH LOCK

ENTER

VIDEO LOCK

OFF

NEW PIN CODE

- - - -

MENU BACK EXIT WATCH TV

Note:

After programming CH Lock, change the channel before turning off the TV.

Usingthe Features

4. Repeat steps 2 and 3 for other channels.

(continued on next page)

37

Appendix

Index

Page 37
Image 37
Mintek 27HL85 owner manual Locking channels, Unlocking programs temporarily, Repeat steps 2 and 3 for other channels