Mitsubishi Electronics MAM-GM6 Mitsubishi Alarm Modem is operational, Mitsubishi Electric

Models: MAM-AM24 MAM-GM6 MAM-AM20 MAM-GM24 MAM-GM20 MAM-AM6

Mitsubishi Alarm Modem is operational

Line-LED when functioning correctly (only GM series)

Manuals / Mitsubishi Electronics / Computer Equipment / Modem

1 48

Download 48 pages 12.13 Kb

Page 28

Image 28

Operation

The device is operational once the self-test is completed and it has “started working”.

If the Mitsubishi Alarm Modem is being commissioned for the first time or after a complete

delete operation (Factory Reset, section 10.2.3), a project must be loaded with the correct

PIN for the SIM card. Note the following instructions in section 7.1 (Initial configuration).

The Mitsubishi Alarm Modem GSM is logged in if the green Line LED flashes at regular intervals.

6 - 2

MITSUBISHI ELECTRIC

Page 28

Image 28

Mitsubishi Electronics MAM-GM6 Mitsubishi Alarm Modem is operational, Line-LED when functioning correctly only GM series

Contents

MITSUBISHI ELECTRIC MITSUBISHI ELECTRIC INDUSTRIAL AUTOMATIONAlarm Modems Instruction Manual Mitsubishi MAM seriesPage About this Manual Page Alarm Modems AM and GM series Instruction ManualArt-No VersionMITSUBISHI ELECTRIC Security Advice Safety instructionsIntended Target Audience Proper useMITSUBISHI ELECTRIC 1 Mitsubishi Alarm Modems at a Glance 3 Installation and Mounting2 Function overview 4 Interfaces5 Power supply 6 Operation 7 Configuration and projects 8 Software9 Communication with a PLC 10 Appendix1 Mitsubishi Alarm Modems at a Glance Communicating possibilities with the Mitsubishi Alarm Modem1.1 State-Of-The-Art Communication 1.2 Easy To Retrofit2.2 Alarming with acknowledgment 2.3 Remote switching via SMS and Express-E-MailAlarms Alarm cascade2.4 Teleservice via PC 2.5 Pump alarm application exampleSecure Login Pump alarm3 Installation and Mounting 3.1 Overview of the Connectors3.1.1 Alarm Modem GSM Fig. 3-1 Overview of all connectors of the Alarm Modem GSMOverview of all connectors of the Alarm Modem 56k 3.1.2 Alarm Modem 56kDescription of the connectors of the Alarm Modem 56k Power 3.2 Meaning of the LEDsProcess Line Data out Fig. 3-3 LEDs on the modem3.3 Mounting Modem mounted on the DIN railDo not subject the device to severe vibration E ATTENTIONMITSUBISHI ELECTRIC 3.4 Connecting the GSM antenna only GM seriesCOM1 RS232 Push down the button until the card holder is released 3.5 Inserting the SIM card only GM seriesE ATTENTION 3.6.1 Testing the Telephone Connection 3.6.2 The CLIP FeatureThe Mitsubishi Alarm Modem supports the a/b leads 3 and 3.6 Connection to the Telephone Network only AM seriesInterfaces COM1 - RS232 Jack4.2 COM2 - RS232 Plug COM14.3 Mitsubishi Alpha XL and Mitsubishi FX at RS232 4.4 RS485 / RS4224.3.1 Alpha XL 4.3.2 Mitsubishi FX1S, FX1N, FX2N, and FX2NCAccess to the DIP switches Fig. 4-6 Position of the DIP switches under the terminal coverThe terminal cover snaps off from the case with an audible click and may beSetting the operating mode on the DIP switch Tab. 4-1 Setting the operating mode on the DIP switchRS485 2-wire connection 2-wire bus system, half-duplex RS422 ConnectionRS485 4-wire connection 4-wire bus system, full-duplex 4.5 Mitsubishi FX at RS485/422Always ensure that the end devices are terminated correctly E ATTENTION5 Power supply Power U = 10 - 30VDCEnsure the correct polarity of the power supply terminals Power supply jack pin = positiveSelf-test after power up 6 OperationMemory test Fig. 6-1 LEDs on modemLine-LED when functioning correctly only GM series Mitsubishi Alarm Modem is operationalMITSUBISHI ELECTRIC 7 Configuration and projects 7.1 Initial configuration7.2 Loading projects in the MAM 7.3 Loading projects remotely on the MAM7.4.5 SIM card disabled, entry of the SUPER PIN 7.4.6 SIM Card Service Center7.4.3 PIN OK, no network, MAM not logged in 7.4.4 PIN incorrect, MAM not logged in7.5.1 Alarm Editor MX-MAE activates the correct mode 7.5.2 Using MAM without MX-MAE7.5 Operating modes Modem Mode and TiXML Mode 7.5.3 TiXML Mode7.5.6 Sending commands to the MAM 7.5.5 Activating/deactivating Modem ModeActivating Modem Mode Deactivating Modem Mode, activating TiXML Mode8.1 MX Mitsubishi Alarm Editor MX-MAE 8.2 Secure Login Access ProtectionFig. 8-1 Mitsubishi Alarm Editor MX-MAE 8 Software8.3 Remote Access MITSUBISHI ELECTRIC9.1 PLC driver in the Mitsubishi Alarm Modem 9 Communication with a PLC10.1 Technical data of the MAM series 10 AppendixMain functions Tab. 10-1 Main functionsTechnical specifications GM series Tab. 10-3 Technical specifications GM seriesTechnical specifications AM series Tab. 10-5 Technical specifications AM seriesTab. 10-7 General data General DataMITSUBISHI ELECTRIC 10.2 LEDs, Reset, Update, Error Diagnostics 10.2.2 LEDs in the event of faults only GM series10.2.3 Factory Reset Tab. 10-9 LEDs in the event of faults10.2.4 Firmware-Update LEDs during factory reset and restartTab. 10-11 LEDs during Factory Reset and restart Tab. 10-10 LEDs during Firmware-Update10.3 Accessories Tab. 10-12 Accessories10.4 Mobile networks in Europe - USA - worldwide Pin assignment10.5 Dimensions Fig. 10-1 Dimensions GM series10.5.1 GM series 10 with Alarm -30 2x V Rs23 Modem DC,max 2+ GSM 6 .0 I/Os .7AFig. 10-2 Dimensions AM series 10.5.2 AM series10 with Alarm -30 2x V Rs23 Modem DC,max 2+ 56k 6 .0 I/Os .7A Modem Mode10.6.1 MAM-GMx Mitsubishi Alarm Modems GSM with RS232 and RS485 10.6 TerminalsMAM-GM6 MAM-GM2010.6.2 MAM-AMx Mitsubishi Alarm Modems 56k with RS232 and RS485 Abb. 10-4 MAM-AMx Mitsubishi Alarm Modems 56k with RS232 and RS485MAM-AM6 MAM-AM20Index Mitsubishi Alarm Modem IndexMITSUBISHI ELECTRIC MITSUBISHI ELECTRIC INDUSTRIAL AUTOMATIONHEADQUARTERS MIDDLE EAST REPRESENTATIVES