Mitsubishi Electronics MSH24WN FEEL... Auto Operation, Description of I FEEL... mode

I FEEL... AUTO OPERATION

•To start operation:

With the “ (I FEEL...)” auto operation mode,		ON/OFF
	Press the	button.

Description of “I FEEL...” mode

the optimum room condition can be set automati-	■
cally with a one-touch operation.

When the “ (I FEEL...)” mode is selected, the air conditioner is automatically controlled at the optimum temperature.

Details of operation

According to the room temperature when the operation starts, the opera- tion mode is automatically set to COOL, DRY or HEAT. However, when operation is started again within 2 hours after it is stopped, the same operation mode before the operation is stopped is selected. The opera- tion mode selected first is not changed even if the room temperature changes. If the operation mode does not match the room condition, se-

Room temperature: About 77 °F or higher

→COOL

˚C

CLOCK AMPM

AMPM

•To stop operation:

■ Press the	ON/OFF
	button.

•If you feel slightly warm:

TOO

■		WARM
	Press the	button to lower the tempera-

lect the appropriate operation mode by pressing the MODE button.

Details of auto operation

Room temperature		Operation mode	Target temperature
when started			(initial state)
About 77	°F or higher	COOL	About 75 °F
About 77	°F - 73 °F	DRY	—
About 73	°F or lower	HEAT	About 79 °F

NOTE

About 77 °F - 73 °F→ DRY About 73 °F or lower

→HEAT

ON/OFF TOO TOO

WARM COOL

FAN	STOP
I FEEL COOL
VANE	START
HEAT DRY
MODE WIDE VANE	HR.
LONG	MIN.
RESET CLOCK

ture.

One press lowers the temperature by about 2 °F.

•If you feel slightly cool:

TOO

■Pressture. the COOL button to raise the tempera-

One press raises the temperature by about 2 °F.

When “ (I FEEL...)” is not selected, press the MODE button until it is set.

Each time the button is pressed, the operation mode is changed in sequence: (I FEEL...) → (COOL) → (DRY)

→(HEAT)

FAN STOP

I FEEL COOL

VANE START

HEAT DRY

MODE WIDE VANE HR.

COOL: When the room temperature is 4 °F higher than the set temperature, the set temperature may not be changed since the air conditioner is operating to reach the target (set) temperature. In this case, please wait until the room temperature drops to within 4 °F of the set temperature and then change the set temperature.

HEAT: When the room temperature is 4 °F lower than the set temperature, the set temperature may not be changed since the air conditioner is operating to reach the target (set) temperature. In this case, please wait until the room temperature rises to within 4 °F of the set temperature and then change the set temperature.

Details of display on the indoor unit

The operation indicator at the right side of the indoor unit indicates the operation state.

		Lighted
	Operation Indicator	Not lighted
Operation indicator lamp
	Indication	Operation state	Difference between target
			temperature and room temperature
		This shows that the air conditioner is operating to reach the
		target temperature. Please wait until the target temperature	About 4 °F or more
		is obtained.
		This shows that the room temperature is approaching the	About 4 °F or less
		target temperature.

ECONO COOL LONG MIN

Description of “AUTO RESTART FUNCTION”

■This unit is equipped with an auto restart function. When the main power is turned on, the air conditioner will start operation automatically in the same mode as the one set with the remote controller before the shutoff of the main power.

■If the unit was set to off with the remote controller before the shutoff of the main power, it will remain stopped even after the main power is turned on.

■If the unit was in the emergency operation before the shutoff of the main power, it will start operation, when main power comes on, in the same mode as the one set with the remote controller before the emergency operation.

■If the unit is operated in “I FEEL ...” mode before power failure, the operation is not stored in the memory. In “I FEEL ...” mode, the operation is decided by the initial room temperature at (re)start.

■Since the air conditioner has been shipped from the factory with the COOL mode saved in the memory for auto restart function, it starts cooling operation when the user turns on the main power for the first time after installation.

7