Paxar 656 / 636 Life Counters Mode

26 • Control Panel Operation Users Manual Model 656/636

• The 650 printer is center justified, meaning the web is centered under

the printhead. The 656 / 636 is a back justified printer, meaning the

web is to the back of the printer. This will not cause a discrepancy

unless the web of the stock does not match the web defined in the

format.

• The verifier will be setup to a specific setting when a verifier is

present. The verifier can be disabled from the front panel.

The <YES / >NO buttons are used to change the emulation.

Pressing ENTER will change the current emulator mode to the new

emulator mode.

Pressing the MODE/Down Arrow key will take the user to the next screen.

Pressing the EXIT/Up Arrow key will take the user back to the HOME

screen.

TRANSFER TYPE:052

NEW TRANSFER TYPE:000

This screen follows the EMULATION MODE screen. This screen allows

the selection of a ink and stock TRANSFER TYPE. See appendix C for

details of ink and stock combinations.

The <YES / >NO buttons are used to increment or decrement each digit.

Pressing ENTER will advance to the next digit. After changing the last

digit, pressing ENTER will change the current transfer type to the new

transfer type. Enter all three digits - including the leading zero.

Pressing the MODE/Down Arrow key will take the user to the next screen.

Pressing the EXIT/Up Arrow key will take the user back to the HOME

screen.

PRESS ENTER TO

PRINT CHECKOUT FORMAT

This screen follows the TRANSFER TYPE screen. This screen allows the

printing of a checkout format.

Pressing ENTER will print the checkout format.

Pressing the MODE/Down Arrow key will take the user to the next screen.

Pressing the EXIT/Up Arrow key will take the user back to the HOME

screen.

Life Counters Mode

Use the Mode ↓ key to move to the following screen.

PRESS ENTER FOR

LIFE COUNTS

Contents

Main Page Contents Page Assembly Drawings 71 Optional Stackers 98 Page Scope Introduction Safety Issues / Warnings Caution Warranty Information Limited Warranty Parts Service Customer Responsibility Location of Printer AC Power Line Unpacking Inventory of Components PAXAR 656 / 636 TOOL KIT (#351390) Printer Setup Installing the Stacker Fuse Configuration Install P.C. Boards as follows: P.C. Board Installation TCB Dip Switch S2 Settings TCB DIP SWITCH S2 SETTINGS Installing the Power Cord Installing the PC Interface Cable Installing the PC Software Product Description Printer Description Personal Computer Specifications Unit Specification Page Printer Operation Installing Ink Ribbon Figure 2 Loading Stock Butt Splice Web Guide Adjustment Print Head Open / Close Control Panel Operation Printer Controls Start Feed Test Stop Indicator Lights On Line Sensor Error Front Panel Menu Functions LCD Display Diagnostic Tests HOME SCREEN Display Modes Print Report Mode Setup Mode Page Life Counters Mode Protected Mode Page Maintenance / Adjustments Print Head Handling Warning P Handling Print Head Cleaning Supplies: Procedure: Print Head Replacement Print Head Adjustment Tangent Clean Platen Roller Print Head Pressure Setting Squaring the Print Head Registration Sensor Adjustment Adjusting Print Sensor Position Cleaning Print Sensor Supplies: Sensor Trim Pots Hole / Slot Index Registration Sensor Reflective Index Registration Sensor Film Out Sensor / Top Ink Sensor Bottom Ink Sensor Headlift Sensor Full Stacker Sensor - Jam Sensor Stock out Adjustment Knife Square Adjustment Stacker Adjustments Stock Length Adjustment Stock Width Adjustment Stacker Angle Adjustment Stacker Full Adjustment Mechanical Adjustment Of Feed Roller Pressure (Blue Roller) Adjustment Procedure: Mechanical Adjustment of Stock Sense - Mark Light Receiver Adjustment Procedure: Page Users Manual Model 656/636 Electrical Connections 41 Electrical Connections Machine Wiring REAR VIEW OF 656 Page Page Motherboard Power Connectors Electrical Trouble Shooting Power Up / Sign On / Communications Page Stock / Ink Advance Page Print Page Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Mechanical Trouble Shooting Stock Page Ink Print Knife Page Mechanical Trouble Shooting Sequence Printer Operation Lubrication Procedure Cam - Lubrication Procedure Composition (Iglide) Bearings Appendix A Error Messages Page Page Page Appendix C Ink and Stock Transfer Types Value Transfer Type Page Appendix D Knife MFG Guideline Other hints if there is still a problem: Page Page Page Page Page Unwind Parts List Page Web Guide / Light Bar Parts List Page Drive Parts List Page Printhead Parts List Page Ink Unwind / Rewind Parts List Page Ink Rewind Arbor Parts List Page Feed & Ink Drive Parts List Page Timing Belt Parts List Page Ink Turn Roller Parts List Page Knife Parts List Page Stacker Parts List Page Rewind Parts List Page Stock Out Sensor Parts List Page Page Page Optional 4.25 Pick-up Parts List Page Optional 4.25 Stacker Parts List Page Optional Down Stacker Parts List (Part 1) Page Optional Down Stacker Parts List (Part 2) Page Optional Down Stacker Parts List (Part 3)