Rear Support Stacker | Paxar 656 / 636 specs

Optional Down Stacker Parts List (Part 2)

Item	Part #	Description	Qty
1	168031	Rear Support Stacker	1
2	168086	Front Stacker Support Assy	1
3	168018	Guide Label	1
4	168027	Platform Slide	1
5	168033	Platform Slide Plate	1
6	168014	Post Stacker Mount	4
7	188008	“T” Nut	2
8	990103	#10 Hex Nut	2
9	990072	8-32 Flat Hd. Screw	4
10	990090	10-32 Button Hd. Screw	2
11	990067	#8 Flat Washer	4
12	990065	8-32 Button Hd. Screw	4

Item	Part #	Description	Qty
13	990092	10-32 Button Hd. Screw	2
14	990729	Nylon Washer	2
15	990053	8-32 Cap Screw	1
16	990314	#8 Thumb Cap	1
17	191120	Micro Switch (Not Shown)	1
18	168039	Label Platform 1 ¼” (Not Shown)	1
19	168040	Label Platform 1 5/8” (Not Shown)	1
20	168041	Label Platform 1 7/8” (Not Shown)	1
21	351125	Stacker Harness (Not Shown)	1
22	371133	Jam Sensor Harness (Not Shown)	1
23	989973	4-40 Cap Screw (Not Shown)	2

Users Manual Model 656/636

Optional Stackers • 107

Image 113

Paxar 656 / 636 user manual Rear Support Stacker

Contents

Paxar Systems Group Manual Edition February Model 656 This page intentionally blank Contents Electrical Connections Assembly Drawings Page Introduction Safety Issues / WarningsScope Limited Warranty Warranty InformationService Parts Location of Printer Customer Responsibility Unpacking AC Power Line Paxar 656 / 636 Tool KIT #351390 Inventory of Components Installing the Stacker Printer Setup Install P.C. Boards as follows Fuse ConfigurationBoard Installation Installing the Power Cord TCB Dip Switch S2 Settings Installing the PC Software Installing the PC Interface Cable Printer Description Product Description Unit Specification Personal Computer Specifications Selfform Paxar Field Engineer Must be Present Installing Ink RibbonPrinter Operation Stock Threading Loading Stock Butt Splice Web Guide Adjustment Figure Print Head Open / Closed Print Head Open / Close Printer Controls Control Panel OperationStart Feed Stop Error Indicator LightsOn Line Sensor Print Reports Front Panel Menu Functions LCD Display Diagnostic Tests Last Batch WAS Imager VXX Ready for Batches Imager VXX Batch ID QTYBuilding Image Imager VXX Display Modes Print Report ModePress Enter for Print Reports Press Enter to Print Last Verifier Scan Setup Mode Change the CUT Cutter is Disabled Press Enter to EnableChange Strobe Strobe 0 NEW Strobe +2 Emulation MODE630 NEW Emulation MODE650 Transfer TYPE052 NEW Transfer TYPE000 Life Counters ModePress Enter to Print Checkout Format Press Enter for Life Counts Protected Mode Verifier is Enabled Press Enter to Disable Change Password 4 Digits NEW WordChange DATE/TIME Press Enter For 2ND Language Handling Maintenance / AdjustmentsPrint Head Handling Supplies Print Head CleaningProcedure Print Head Replacement Clean Platen Roller Print Head AdjustmentPrint Head Pressure Setting Tangent Adjusting Print Sensor Position Registration Sensor AdjustmentSquaring the Print Head Print Head Tangent Point Sensor Trim Pots Cleaning Print Sensor Hole / Slot Index Registration Sensor DIP Switch Bank Lights Film Out Sensor / Top Ink Sensor Reflective Index Registration SensorBottom Ink Sensor TP8 Knife Square Adjustment Stock out AdjustmentHeadlift Sensor Full Stacker Sensor Jam Sensor Stock Feed Adjustment Stacker Adjustments Mechanical Adjustment of Stock Sense Mark Light Receiver Mechanical Adjustment Of Feed Roller Pressure Blue RollerAdjustment Procedure GeneralPage Electrical Connections Machine Wiring Relay Assembly Electrical System Schematic Motherboard Power Connectors Power Up / Sign On / Communications Electrical Trouble Shooting Problem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Stock Mechanical Trouble Shooting Problem Probable Cause Corrective Action Ink Print Knife Problem Probable Cause Corrective Action TCB Lubrication Procedure Mechanical Trouble Shooting SequenceCam Lubrication Procedure Composition Iglide Bearings Appendix a Error Messages Thermal Control Board P/N Software Upgrade Chip Placement PositionsAppendix B Head Driver Board P/N Diskless Rom Board P/N Front Panel Board P/N Ink and Stock Transfer Types Appendix C Value Transfer Type Value Transfer Type Knife MFG Guideline Appendix D Appendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Description Qty Unwind Parts List Web Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Field Retrofit Kit Ink Rewind Arbor Assembly Ink Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Part Qty Description Number Knife Parts List Stacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Part Qty Description Number Stock Out Sensor Parts List Optional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap