Optional 4.25 Stacker Parts List | Paxar 656 / 636 guide

Optional 4.25” Stacker Parts List

Item	Part #	Description	Qty
1	378205	Plate Stacker Support	1
2	378288	Rear Side Frame Assy	1
3	378289	Front Side Frame Assy	1
4	378212	Drive Roller	1
5	378214	Drive Shaft	1
6	378130	Rail Slide Bracket	2
7	378209	Mount Stacker Rail	1
8	378210	Base Stacker Rail	1
9	38215	Stacker Upright Front	1
10	378035	Stacker Upright Rear	1
11	378046	Belt Guard	1
12	351161	Stacker Motor Harnessed	1
13	284022	Pulley Drive Belt	2
14	188008	“T” Nut	4
15	990081	10-32 Cap Screw	2
16	990102	#10 Washer	2

Item	Part #	Description	Qty
17	990028	6-32 Flat Hd. Screw	4
18	990079	10-32 Cap Screw	2
19	990313	#10 Thumb Screw Knob	4
20	990641	#6 Wing Nut	1
21	990037	#6 Washer	1
22	990080	10-32 Cap Screw	2
23	990262	¼” Snap Ring	1
24	990019	6-32 Button Hd. Screw	2
25	990369	1/8” Collar	2
26	184002	Web Guide Thumb Screw	1
27	351125	Stacker Harness (NS)	1
28	351160	Full Stacker Harn. (NS)	1
29	371133	Jam Sensor Harn. (NS)	1
30	358018	Timing Belt (NS)	1
31	990006	4-40 Cap Screw	2

Users Manual Model 656/636

Optional Stackers • 103

Image 109

Paxar 656 / 636 user manual Optional 4.25 Stacker Parts List

Contents

Paxar Systems Group Manual Edition February Model 656 This page intentionally blank Contents Electrical Connections Assembly Drawings Page Scope Safety Issues / WarningsIntroduction Limited Warranty Warranty InformationService Parts Location of Printer Customer Responsibility Unpacking AC Power Line Paxar 656 / 636 Tool KIT #351390 Inventory of Components Installing the Stacker Printer Setup Board Installation Fuse ConfigurationInstall P.C. Boards as follows Installing the Power Cord TCB Dip Switch S2 Settings Installing the PC Software Installing the PC Interface Cable Printer Description Product Description Unit Specification Personal Computer Specifications Selfform Printer Operation Installing Ink RibbonPaxar Field Engineer Must be Present Stock Threading Loading Stock Butt Splice Web Guide Adjustment Figure Print Head Open / Closed Print Head Open / Close Printer Controls Control Panel OperationStart Feed Stop Error Indicator LightsOn Line Sensor Print Reports Front Panel Menu Functions LCD Display Diagnostic Tests Building Image Imager VXX Ready for Batches Imager VXX Batch ID QTYLast Batch WAS Imager VXX Display Modes Print Report ModePress Enter for Print Reports Press Enter to Print Last Verifier Scan Setup Mode Change the CUT Cutter is Disabled Press Enter to EnableChange Strobe Strobe 0 NEW Strobe +2 Emulation MODE630 NEW Emulation MODE650 Transfer TYPE052 NEW Transfer TYPE000 Life Counters ModePress Enter to Print Checkout Format Press Enter for Life Counts Protected Mode Verifier is Enabled Press Enter to Disable Change Password 4 Digits NEW WordChange DATE/TIME Press Enter For 2ND Language Print Head Handling Maintenance / AdjustmentsHandling Procedure Print Head CleaningSupplies Print Head Replacement Clean Platen Roller Print Head AdjustmentPrint Head Pressure Setting Tangent Adjusting Print Sensor Position Registration Sensor AdjustmentSquaring the Print Head Print Head Tangent Point Sensor Trim Pots Cleaning Print Sensor Hole / Slot Index Registration Sensor DIP Switch Bank Lights Film Out Sensor / Top Ink Sensor Reflective Index Registration SensorBottom Ink Sensor TP8 Knife Square Adjustment Stock out AdjustmentHeadlift Sensor Full Stacker Sensor Jam Sensor Stock Feed Adjustment Stacker Adjustments Mechanical Adjustment of Stock Sense Mark Light Receiver Mechanical Adjustment Of Feed Roller Pressure Blue RollerAdjustment Procedure GeneralPage Electrical Connections Machine Wiring Relay Assembly Electrical System Schematic Motherboard Power Connectors Power Up / Sign On / Communications Electrical Trouble Shooting Problem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Stock Mechanical Trouble Shooting Problem Probable Cause Corrective Action Ink Print Knife Problem Probable Cause Corrective Action TCB Lubrication Procedure Mechanical Trouble Shooting SequenceCam Lubrication Procedure Composition Iglide Bearings Appendix a Error Messages Appendix B Software Upgrade Chip Placement PositionsThermal Control Board P/N Head Driver Board P/N Diskless Rom Board P/N Front Panel Board P/N Ink and Stock Transfer Types Appendix C Value Transfer Type Value Transfer Type Knife MFG Guideline Appendix D Appendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Description Qty Unwind Parts List Web Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Field Retrofit Kit Ink Rewind Arbor Assembly Ink Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Part Qty Description Number Knife Parts List Stacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Part Qty Description Number Stock Out Sensor Parts List Optional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap