Printer Setup, Installing the Stacker | Paxar 656 / 636 specification

Printer Setup

Installing the Stacker

Remove the stacker from the separate packaging. Remove the packaging from around the stacker and save with the rest of the printer packing supplies.

Swing open the top cover to the printer. Locate the large knob and two round pins on the right hand side of the printer. Loosen the knob enough to allow the stacker to slide between the printer housing and the knob. The stacker will rest on the two pins. Slide the stacker to the back until it contacts the up-right frame. Tighten the knob. Adjusting the stacker is covered later.

Install the stacker up-right rails. Remove one of the thumb screws. Insert the thumb screw through the mating hole in the up-right rail assembly. Thread the thumb screw into the mounting block. Repeat the above procedure for the other thumb screw.

There is a harness and connector leading from the back of the stacker that plugs into the center connector on the last PC board. The connector and plug are polarized. Rotate the plug until the polarized plug and connector align and push them together.

6 • Printer Setup

Users Manual Model 656/636

Image 12

Paxar 656 / 636 user manual Printer Setup, Installing the Stacker

Contents

Model 656 Paxar Systems Group Manual Edition February This page intentionally blank Contents Electrical Connections Assembly Drawings Page Safety Issues / Warnings ScopeIntroduction Warranty Information Limited WarrantyService Parts Customer Responsibility Location of Printer AC Power Line Unpacking Inventory of Components Paxar 656 / 636 Tool KIT #351390 Printer Setup Installing the Stacker Fuse Configuration Board InstallationInstall P.C. Boards as follows TCB Dip Switch S2 Settings Installing the Power Cord Installing the PC Interface Cable Installing the PC Software Product Description Printer Description Personal Computer Specifications Unit Specification Selfform Installing Ink Ribbon Printer OperationPaxar Field Engineer Must be Present Loading Stock Stock Threading Web Guide Adjustment Butt Splice Print Head Open / Close Figure Print Head Open / Closed Control Panel Operation Printer ControlsStart Feed Stop Indicator Lights ErrorOn Line Sensor Front Panel Menu Functions Print Reports Diagnostic Tests LCD Display Ready for Batches Imager VXX Batch ID QTY Building Image Imager VXXLast Batch WAS Imager VXX Print Report Mode Display ModesPress Enter for Print Reports Press Enter to Print Last Verifier Scan Setup Mode Cutter is Disabled Press Enter to Enable Change the CUTChange Strobe Strobe 0 NEW Strobe +2 Emulation MODE630 NEW Emulation MODE650 Life Counters Mode Transfer TYPE052 NEW Transfer TYPE000Press Enter to Print Checkout Format Press Enter for Life Counts Protected Mode Change Password 4 Digits NEW Word Verifier is Enabled Press Enter to DisableChange DATE/TIME Press Enter For 2ND Language Maintenance / Adjustments Print Head HandlingHandling Print Head Cleaning ProcedureSupplies Print Head Replacement Print Head Adjustment Clean Platen RollerPrint Head Pressure Setting Tangent Registration Sensor Adjustment Adjusting Print Sensor PositionSquaring the Print Head Print Head Tangent Point Cleaning Print Sensor Sensor Trim Pots DIP Switch Bank Lights Hole / Slot Index Registration Sensor Reflective Index Registration Sensor Film Out Sensor / Top Ink SensorBottom Ink Sensor TP8 Stock out Adjustment Knife Square AdjustmentHeadlift Sensor Full Stacker Sensor Jam Sensor Stacker Adjustments Stock Feed Adjustment Mechanical Adjustment Of Feed Roller Pressure Blue Roller Mechanical Adjustment of Stock Sense Mark Light ReceiverAdjustment Procedure GeneralPage Machine Wiring Electrical Connections Relay Assembly Electrical System Schematic Motherboard Power Connectors Electrical Trouble Shooting Power Up / Sign On / Communications Problem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Mechanical Trouble Shooting Stock Problem Probable Cause Corrective Action Ink Print Problem Probable Cause Corrective Action Knife TCB Mechanical Trouble Shooting Sequence Lubrication ProcedureCam Lubrication Procedure Composition Iglide Bearings Error Messages Appendix a Software Upgrade Chip Placement Positions Appendix BThermal Control Board P/N Diskless Rom Board P/N Head Driver Board P/N Front Panel Board P/N Appendix C Ink and Stock Transfer Types Value Transfer Type Value Transfer Type Appendix D Knife MFG Guideline Appendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Unwind Parts List Description Qty Web Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Ink Rewind Arbor Assembly Field Retrofit Kit Ink Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Knife Parts List Part Qty Description Number Stacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Stock Out Sensor Parts List Part Qty Description Number Optional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap