Inventory of Components | Paxar 656 / 636 instruction

In some cases, a double box has been used to ship your printer.

Figure 1b Shipping Carton.

Save the shipping materials to relocate the unit or return to factory for service.

Inventory of Components

The following list shows the additional parts (pieces) which should be included in your PAXAR 656 / 636 shipping container. If anything is missing, notify PAXAR immediately - in the U.S.A. at 570-888-9116. In other countries please contact your local PAXAR supplier.

-PAXAR 656 / 636 "User's Manual"

-Tool kit

-A quick-disconnect power cord

-Optional IC card for custom Logos or additional fonts that were special ordered. (in the back of the manual)

-Stacker assembly

-Optional software ordered to drive the printer.

-A serial communications cable

NOTE: Some of the above parts may be inside of the envelope which contains the tool kit.

PAXAR 656 / 636 TOOL KIT (#351390)

241149	Anti-Static Gloves (2)
921309	Hex Key Set
921316	3/16" Long Ball Driver
181301	2.5mm Ball Driver
301156	Chip Removal Tool
351398	656 / 636 Users Manual

Users Manual Model 656/636

Customer Responsibility • 5

Image 11

Paxar user manual Inventory of Components, Paxar 656 / 636 Tool KIT #351390

Contents

Paxar Systems Group Manual Edition February Model 656 This page intentionally blank Contents Electrical Connections Assembly Drawings Page Introduction Safety Issues / WarningsScope Parts Warranty InformationLimited Warranty Service Location of Printer Customer Responsibility Unpacking AC Power Line Paxar 656 / 636 Tool KIT #351390 Inventory of Components Installing the Stacker Printer Setup Install P.C. Boards as follows Fuse ConfigurationBoard Installation Installing the Power Cord TCB Dip Switch S2 Settings Installing the PC Software Installing the PC Interface Cable Printer Description Product Description Unit Specification Personal Computer Specifications Selfform Paxar Field Engineer Must be Present Installing Ink RibbonPrinter Operation Stock Threading Loading Stock Butt Splice Web Guide Adjustment Figure Print Head Open / Closed Print Head Open / Close Feed Control Panel OperationPrinter Controls Start Stop Sensor Indicator LightsError On Line Print Reports Front Panel Menu Functions LCD Display Diagnostic Tests Last Batch WAS Imager VXX Ready for Batches Imager VXX Batch ID QTYBuilding Image Imager VXX Press Enter to Print Last Verifier Scan Print Report ModeDisplay Modes Press Enter for Print Reports Setup Mode Emulation MODE630 NEW Emulation MODE650 Cutter is Disabled Press Enter to EnableChange the CUT Change Strobe Strobe 0 NEW Strobe +2 Press Enter for Life Counts Life Counters ModeTransfer TYPE052 NEW Transfer TYPE000 Press Enter to Print Checkout Format Protected Mode Press Enter For 2ND Language Change Password 4 Digits NEW WordVerifier is Enabled Press Enter to Disable Change DATE/TIME Handling Maintenance / AdjustmentsPrint Head Handling Supplies Print Head CleaningProcedure Print Head Replacement Tangent Print Head AdjustmentClean Platen Roller Print Head Pressure Setting Print Head Tangent Point Registration Sensor AdjustmentAdjusting Print Sensor Position Squaring the Print Head Sensor Trim Pots Cleaning Print Sensor Hole / Slot Index Registration Sensor DIP Switch Bank Lights TP8 Reflective Index Registration SensorFilm Out Sensor / Top Ink Sensor Bottom Ink Sensor Full Stacker Sensor Jam Sensor Stock out AdjustmentKnife Square Adjustment Headlift Sensor Stock Feed Adjustment Stacker Adjustments General Mechanical Adjustment Of Feed Roller Pressure Blue RollerMechanical Adjustment of Stock Sense Mark Light Receiver Adjustment ProcedurePage Electrical Connections Machine Wiring Relay Assembly Electrical System Schematic Motherboard Power Connectors Power Up / Sign On / Communications Electrical Trouble Shooting Problem Probable Cause Corrective Action Stock / Ink Advance Problem Probable Cause Corrective Action Print Problem Probable Cause Corrective Action Cut / Stack Electrical Trouble Shooting / Machine Set Up Sequence Stock Mechanical Trouble Shooting Problem Probable Cause Corrective Action Ink Print Knife Problem Probable Cause Corrective Action TCB Composition Iglide Bearings Mechanical Trouble Shooting SequenceLubrication Procedure Cam Lubrication Procedure Appendix a Error Messages Thermal Control Board P/N Software Upgrade Chip Placement PositionsAppendix B Head Driver Board P/N Diskless Rom Board P/N Front Panel Board P/N Ink and Stock Transfer Types Appendix C Value Transfer Type Value Transfer Type Knife MFG Guideline Appendix D Appendix D Appendix D Page Assembly Drawings Unwind Assembly Drawing Description Qty Unwind Parts List Web Guide / Light Bar Assembly Drawing Web Guide / Light Bar Parts List Drive Assembly Drawing Drive Parts List Printhead Assembly Drawing Printhead Parts List Ink Unwind / Rewind Assembly Ink Unwind / Rewind Parts List Field Retrofit Kit Ink Rewind Arbor Assembly Ink Rewind Arbor Parts List Feed & Ink Drive Assembly Feed & Ink Drive Parts List Timing Belt Threading Diagram Timing Belt Parts List Ink Turn Roller Assembly Ink Turn Roller Parts List Knife Assembly Drawing Part Qty Description Number Knife Parts List Stacker Assembly Drawing Stacker Parts List Rewind Assembly Drawing Rewind Parts List Stock Out Sensor Assembly Drawing Part Qty Description Number Stock Out Sensor Parts List Optional Stackers Stacker Specifications Optional 4.25 Pick-up Assembly Optional 4.25 Pick-up Parts List Optional 4.25 Stacker Assembly Optional 4.25 Stacker Parts List Optional Down Stacker Assembly Drawing Part Optional Down Stacker Parts List Part Optional Down Stacker Assembly Drawing Part Rear Support Stacker Optional Down Stacker Assembly Drawing Part #8 Thumb Screw Cap