7.Other Functions
7.2.Error Codes indication
ERROR CODE
ON/OFF
Indoor Unit’s Refrig- Error Code | Indoor Unit No. | |||
erant Address |
|
|
| |
|
| Alternating Display | ||
If you have entered contact number to be called in the event of a problem, the screen displays this number. |
| |||
|
|
|
| |
(You can set this up under Function Selection of remote controller. For information, refer to section 8.) |
|
|
|
|
|
|
|
|
|
ON lamp (Flashing)
●If the ON lamp and error code are both flashing: This means that the air conditioner is out of order and operation has been stopped (and cannot resume). Take note of the indicated unit number and error code, then switch off the power to the air conditioner and call your dealer or servicer.
˚F |
| When the Check button is pressed: |
| CALL:XXXX |
ERROR CODE | XXX:XXX |
˚F |
|
ON/OFF | ON/OFF |
Error Code
●If only the error code is flashing (while the ON lamp remains lit): Operation is continuing, but there may be a problem with the system. In this case, you should note down the error code and then call your dealer or servicer for advice.
*If you have entered contact number to be called in the event of a problem, push the Check button to display it on the screen. (You can set this up under Function Selection of remote controller. For information, refer to section 8.)
8. Function Selection
Function selection of remote controller
The setting of the following remote controller functions can be changed using the remote controller function selection mode. Change the setting when needed.
Item 1 |
| Item 2 | Item 3 (Setting content) | |
|
|
| ||
1. Change Language | Language setting to display | • Display in multiple languages is possible | ||
(“CHANGE |
|
|
| |
LANGUAGE”) |
|
|
| |
|
|
|
| |
2. Function limit | (1) | Operation function limit setting (operation lock) (“LOCKING | • Setting the range of operation limit (operation lock) | |
(“FUNCTION |
| FUNCTION”) |
| |
SELECTION”) |
|
|
| |
(2) | Use of automatic mode setting (“SELECT AUTO MODE”) | • Setting the use or | ||
| ||||
|
|
| ||
| (3) Temperature range limit setting (“LIMIT TEMP FUNCTION”) | • Setting the temperature adjustable range (maximum, minimum) | ||
|
|
|
| |
3. Mode selection | (1) | Remote controller main/sub setting (“CONTROLLER MAIN/ | • Selecting main or sub remote controller | |
| SUB”) | * When two remote controllers are connected to one group, one controller | ||
(“MODE SELEC- |
| |||
|
| must be set to sub. | ||
TION”) |
|
| ||
|
|
| ||
| (2) | Use of clock setting (“CLOCK”) | • Setting the use or | |
|
|
| ||
| (3) Timer function setting (“WEEKLY TIMER”) | • Setting the timer type | ||
|
|
|
| |
| (4) | Contact number setting for error situation (“CALL.”) | • Contact number display in case of error | |
|
|
| • Setting the telephone number | |
|
|
| ||
4. Display change | (1) Temperature display °C/°F setting (“TEMP MODE °C/°F”) | • Setting the temperature unit (°C or °F) to display | ||
(“DISP MODE |
|
|
| |
(2) | Suction air temperature display setting (“ROOM TEMP DISP | • Setting the use or | ||
SETTING”) | ||||
| SELECT”) | ture | ||
|
| |||
|
|
|
| |
| (3) | Automatic cooling/heating display setting (“AUTO MODE | • Setting the use or | |
|
| DISP C/H”) | during operation with automatic mode | |
|
|
|
| |
12
