7. Test run

[Output pattern B] Errors detected by unit other than indoor unit (outdoor unit, etc.)

Wireless remote controller

Wired remote

 

 

controller

 

 

 

 

 

Beeper sounds/OPERATION

 

Symptom

Remark

INDICATOR lamp flashes

Check code

 

 

(Number of times)

 

 

 

 

 

 

 

1

E9

Indoor/outdoor unit communication error (Transmitting error) (Outdoor unit)

 

2

UP

Compressor overcurrent interruption

 

3

U3, U4

Open/short of outdoor unit thermistors

 

4

UF

Compressor overcurrent interruption (When compressor locked)

 

5

U2

Abnormal high discharging temperature/49C worked/insufficient refrigerant

 

6

U1, Ud

Abnormal high pressure (63H worked)/Overheating safeguard operation

 

7

U5

Abnormal temperature of heat sink

For details, check the LED display

8

U8

Outdoor unit fan safeguard stop

of the outdoor controller board.

9

U6

Compressor overcurrent interruption/Abnormal of power module

 

10

U7

Abnormality of super heat due to low discharge temperature

 

11

U9, UH

Abnormality such as overvoltage or voltage shortage and abnormal synchronous

 

 

 

signal to main circuit/Current sensor error

 

 

 

 

 

12

 

 

 

 

 

13

 

 

 

 

 

14

Others

Other errors (Refer to the technical manual for the outdoor unit.)

 

*1 If the beeper does not sound again after the initial two beeps to confirm the self-check start signal was received and the OPERATION INDICATOR lamp does not come on, there are no error records.

*2 If the beeper sounds three times continuously “beep, beep, beep (0.4 + 0.4 + 0.4 sec.)” after the initial two beeps to confirm the self-check start signal was received, the specified refrigerant address is incorrect.

On wireless remote controller

The continuous buzzer sounds from receiving section of indoor unit. Blink of operation lamp

On wired remote controller Check code displayed in the LCD.

If the unit cannot be operated properly after the above test run has been performed, refer to the following table to remove the cause.

 

Symptom

 

Cause

 

 

 

Wired remote controller

LED 1, 2 (PCB in outdoor unit)

 

 

For about 2

After LED 1, 2 are lighted, LED 2 is turned off,

• For about 2 minutes following power-on, operation of the

PLEASE WAIT

minutes following

remote controller is not possible due to system start-up. (Cor-

then only LED 1 is lighted. (Correct operation)

 

power-on

rect operation)

 

 

 

 

 

 

 

 

 

• Connector for the outdoor unit’s protection device is not con-

PLEASE WAIT Error code

 

Only LED 1 is lighted. LED 1, 2 blink.

nected.

After about 2

• Reverse or open phase wiring for the outdoor unit’s power

 

 

 

minutes has

 

terminal block (L1, L2, GR)

Display messages do not appear even

expired following

 

• Incorrect wiring between indoor and outdoor units (incorrect

power-on

Only LED 1 is lighted. LED 1 blinks twice,

polarity of S1, S2, S3)

when operation switch is turned ON

 

LED 2 blinks once.

(operation lamp does not light up).

 

• Remote controller wire short

 

 

 

 

 

 

On the wireless remote controller with condition above, following phenomena takes place.

No signals from the remote controller are accepted.

OPE lamp is blinking.

The buzzer makes a short pipng sound.

Note:

Operation is not possible for about 30 seconds after cancellation of function selection. (Correct operation)

For description of each LED (LED 1, 2, 3) provided on the indoor controller, refer to the following table.

LED 1

(power for microcomputer)

Indicates whether control power is supplied. Make sure that this LED is always lit.

 

 

 

LED 2

(power for remote controller)

Indicates whether power is supplied to the remote controller. This LED lights only in the case of the

 

 

indoor unit which is connected to the outdoor unit refrigerant address “0”.

LED 3 (communication between indoor and outdoor units only A-control)

Indicates state of communication between the indoor and outdoor units. Make sure that this LED is

 

 

always blinking.

14

Page 14
Image 14
Mitsubishi Electronics PKA-A-GA Outdoor unit fan safeguard stop, Outdoor controller board, Minutes following

PKA-A-GA specifications

Mitsubishi Electronics has long been a key player in the realm of air conditioning and climate control technologies, offering a range of innovative solutions that cater to both residential and commercial needs. Among their impressive lineup, the Mitsubishi PKA-A-GA stands out as a noteworthy model known for its advanced features, efficiency, and reliability.

The Mitsubishi PKA-A-GA is a wall-mounted air conditioning unit specifically designed for easy installation and optimal performance. One of its main features is the sleek and modern design, which allows it to blend seamlessly with various interior settings. Its compact form factor saves space while maximizing cooling efficiency.

This model utilizes cutting-edge inverter technology, which significantly enhances energy efficiency. By adjusting the compressor speed according to the cooling demand, the PKA-A-GA maintains a consistent temperature while reducing energy consumption. This not only lowers utility bills but also contributes to a more sustainable operation, making the unit eco-friendly.

A remarkable characteristic of the PKA-A-GA is its advanced air filtration system. Equipped with a high-performance filter, the unit effectively removes allergens, dust, and other particulates from the indoor air, ensuring a cleaner and healthier environment. Additionally, the unit features a self-cleaning function, which helps maintain the filter's efficiency by reducing the buildup of dust and other particles.

Another compelling aspect of the Mitsubishi PKA-A-GA is its whisper-quiet operation. The unit is designed to minimize noise, making it ideal for bedrooms, offices, and other spaces where tranquility is essential. This is particularly beneficial for users who require a calm atmosphere for work or relaxation.

Furthermore, the PKA-A-GA is compatible with smart controls, allowing users to operate and monitor their air conditioning system remotely via smartphones or tablets. This feature adds convenience and lets users optimize their energy consumption even when they're away from home.

Lastly, the durability of the Mitsubishi PKA-A-GA is noteworthy. Built with high-quality materials and robust components, this air conditioning unit is designed to withstand the rigors of daily use while providing reliable performance over the years.

Overall, the Mitsubishi PKA-A-GA is an exceptional air conditioning solution, blending efficiency, smart technology, and user-friendly features into a compact design. Whether for residential or commercial applications, it promises to deliver comfort and satisfaction in an ever-evolving climate.