Troubleshooting, continued

 

Problem

Possible Solution

 

 

 

 

50.

 

Program to be recorded was correctly selected

The broadcaster supplied program information that was incorrect and/

 

 

from ChannelView, however, incorrect program

or was changed after a recording was added to the Record List.

 

 

was recorded.

 

 

 

 

 

51.

 

Incomplete ChannelView program recorded.

Recording device may have lack of space availability and there is not

 

 

 

enough blank space to make a full recording.

 

 

 

 

52.

 

ChannelView program recording failed.

• Connection and compatibility issues with IEEE 1394 (FireWire®)

 

 

 

digital devices. This may include too many FireWire devices in use

 

 

 

at one time, or the recording device not understanding the record

 

 

 

command.

 

 

 

• Television lost power long enough to lose current clock time.

 

 

 

• Analog VCR power was left Off.

 

 

 

 

53.

 

TV Guide On Screen® system shows no program

• Program listings are downloaded while the TV is off and cable box

 

 

listings.

is left on. It may take up to 24 hours to begin to receive TV program

 

 

 

listings. It may take up to one week to receive all eight days of TV

 

 

 

program listings.

 

 

 

• Invalid ZIP code was entered at the initial TV Guide On Screen

 

 

 

system setup. Select NetCommand from the main TV menu, then

 

 

 

Guide and enter the correct ZIP code.

 

 

 

• Check the connections between the TV and the TV Guide On Screen

 

 

 

input (cable, antenna or cable box and IR cable). At least one

 

 

 

antenna connection must be associated with the TV Guide On Screen

 

 

 

system to receive program listings.

 

 

 

 

54.

 

TV Guide On Screen system program listings

• Incorrect ZIP code was entered at initial TV Guide On Screen system

 

 

don’t match actual programs

setup. Select NetCommand menu, then Guide to enter the correct

 

 

 

ZIP code.

 

 

 

• For cable programs, there may be more than one cable company in

 

 

 

your ZIP code. Refer to the TV Guide On Screen Interactive Program

 

 

 

Guide User’s Manual for instructions on the Setup Service.

 

 

 

• Ensure that only one cable source is check marked in the

 

 

 

NetCommand setup for TV Guide On Screen.

 

 

 

 

55.

 

TV Guide On Screen system does not change

• Cable box is not set up in NetCommand. The TV Guide On Screen

 

 

channels on the cable box.

system uses NetCommand to control the cable box and VCR. To

 

 

 

correct, select NetCommand from the main TV menu, then select

 

 

 

Change or Add on the NetCommand menu.

 

 

 

• IR emitter is not in place or properly positioned in front of the cable

 

 

 

box remote sensor. See page 31.

 

 

 

• Ensure that the cable box is turned on.

 

 

 

 

56.

 

I set up a TV Guide On Screen recording to my

• Analog content can only be recorded to an analog recording device,

 

 

digital recorder, but the recording failed and I

such as a VCR. Open the TV Guide On Screen Record Options menu

 

 

got an error message saying it cannot record an

and change the destination recorder to match the analog recording

 

 

analog program.

device connected to the TV RECORD OUTPUT jacks.

 

 

 

 

Demo Mode

This TV has a demo mode for use in retail stores. To turn demo mode On/Off, press the following buttons in sequence:

MENU, 0, QV, 0

Using the System Reset Button

If the TV doesn’t respond to either the remote control or the front panel controls, or will not power off, press the SYSTEM RESET button on the front panel with a pointed item such as the point of a ball point pen or end tip of a paperclip.

The TV will turn off and the green LED will flash quickly for about one minute. When the green LED stops flashing, you may turn on the TV again. The changes you made while the TV was most recently on, before you used the SYSTEM RESET button, may be lost, although the changes you made previously are not lost. Only those changes since the last power On may be lost when the system reset button is pressed. All other settings are retained.

102 Chapter 6. Special Features

Page 102
Image 102
Mitsubishi Electronics WD-52527 manual Demo Mode, MENU, 0, QV