Mitsubishi Electronics WD-52527 manual Receiver Stereo System, To connect an analog A/V receiver

Connecting an A/V Receiver (Stereo System)

Connecting a Satellite Receiver or Other Device with S -Video

A/V Receiver (Stereo System)

Figure 7

A coaxial digital audio cable or stereo audio cables are required. These cables are not provided with the TV.

•To connect an analog A/V receiver:

Connect a set of stereo audio cables from OUTPUT AUDIO 2 on the TV back panel to the TV AUDIO INPUT on the back of the A/V receiver. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

•To connect a digital A/V receiver with Dolby® Digital surround sound:

Connect one end of a digital audio cable to DIGITAL AUDIO on the back of the TV. Connect the other end to the COAXIAL DIGITAL INPUT on the back of the A/V receiver.

57
CBDL
QBOFM

INPUT

1

2

Y

INPUT

OUTPUT

DVI

AUDIO

RECORD

S-VIDEO

Pb

Analog Audio

OUTPUT

OUTPUT

1

2

VIDEO



Pr

8IJUF

VIDEO

AUDIO-

LEFT/

(MONO)

AUDIO-

AUDIO-

LEFT/

LEFT/

AUDIO-

(MONO)

(MONO)

3FE

RIGHT

AUDIO-

AUDIO-

RIGHT

RIGHT

MONIT

VIDEO 480i/480p/720p/1080i

AUDIO PCM LINEAR

1

VICE

',INK

¸

DIGITAL

CableCARD

AUDIO

CableCARD™ USE WITH ANT 1 CARD TOP

ANT 1 / MAIN

ANT 2 / AUX

OUTPUT

EE1394

NPUT/

UTPUT



6TF JG

6TF JG

DPOOFDUJOH

DPOOFDUJOH B

BO BOBMPH

%PMCZ EJHJUBM

"7 SFDFJWFS

"7 SFDFJWFS

Satellite Receiver or Other Device with S-Video

Figure 8

An S-Video cable and audio cables are required. These are not included with the TV.

1.Connect an S-Video cable from VIDEO OUT on the satellite receiver back panel to INPUT-2 VIDEO on the TV back panel.

2.Connect a set of audio cables from AUDIO OUT on the satellite receiver back panel to INPUT-2 AUDIO, on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

Note: Refer to the Satellite Receiver Owner’s Guide for Dish Antenna connections.

57
CBDL
QBOFM
TFDUJPO

INPUT

1 2

S-VIDEO

VIDEO

8IJUF

AUDIO-

LEFT/

(MONO)

AUDIO-

RIGHT

3FE



"7
3FDFJWFS
3FBS
1BOFM

			BOZ 4WJEFP EFWJDF
					"6%*0 065	"6%*0 */		7*%&0 065	
			*/165	8IJUF
			$0"9*"-
					-		-	:$
				3FE		
8IJUF					3		3
		-
3FE		3
		57
		*/
Figure 7.	Connecting an A/V receiver		Figure 8. Connecting a Satellite Receiver with S-Video

Note: On rare occasions, an HDMI signal may be copy-restricted and cannot be output from the TV as a digital signal. This is not anticipated to be a common situation. To hear these copy-protected signals through the A/V receiver, use connections for analog A/V receivers.

Note: NetCommand® will assume you connected your Satellite Receiver to Input-2. If you add a second Satellite Receiver or use any other inputs for your Satellite Receiver, this change must match in the NetCommand system. See Editing NetCommand Setup in Chapter 3 for more information.

28 Chapter 2. Connecting