Mitsubishi Electronics XD500U-ST Advanced features, Freeze, Procedure, Page-up and page-down

Advanced features

Displaying a user-defined image during startup or mut- ing

You can display your desired image as the startup screen (or splash screen). Using the menu, you can also use it as the background that is displayed while the video is muted or no signal is input.

Important:

•You can't select IMAGE CAPTURE when PASSWORD FUNC- TION in the FEATURE menu is set to SPLASH ID SCREEN to activate the password lock.

•You can't select IMAGE CAPTURE when the component video signal is input.

Procedure

1.Press the COMPUTER button to select the image input to the COMPUTER/COMPONENT VIDEO IN terminal.

2.Display your desired image.

3.Display the INSTALLATION menu.

4.Select IMAGE CAPTURE by pressing the S or T button.

5.Press the ENTER button.

	opt.
INSTALLATION
	WALL SCREEN	BEIGE
	LAMP MODE	STANDARD
	AUTO POWER	OFF
	ON
	AUTO POWER	OFF
	OFF
	IMAGE	GO
	CAPTURE
ON	SPLASH	ON
	SCREEN
	BACK COLOR	BLUE
	MUTE MODE	BLACK
	IMAGE	OFF
	REVERSE

•When the capture starts, the captured image will be dis- played.

•When you press ENTER button once, any button doesn't function until the capture completes.

•When image resolution is lower than XGA(1024 x 768), the image is captured by adjusting its resolution to XGA.

•When image resolution is higher than XGA(1024 x 768), the image area of XGA is only captured.

Important:

•You can't change the new startup screen back to the original screen. (Even when you select RESET ALL in the FEATURE menu, the factory default screen is no longer effective.) When you want to change the startup screen again, capture another image.

•The captured images will be deleted at the same time as pressing the ENTER button. If you pressed ENTER button wrongly, try to capture the same images again.

•The captured image is displayed from the next startup. If the cap- tured image isn't displayed, check to see if SPLASH SCREEN in the INSTALLATION menu is set to OFF. (See page 18.)

•To display the captured image while the video is muted, set AV MUTE MODE in the INSTALLATION menu to IMAGE. (See page 18.)

•When BACK COLOR in the INSTALLATION menu is set to IMAGE, the captured image is displayed while no signal is input.

•Some images can't be captured correctly because of their signal type.

Freeze

To stop the motion in the image temporarily (or to dis- play a still image):

Press the FREEZE button on the remote control.

•The image freezes temporarily.

To resume the motion in the image:

Press the FREEZE button on the remote control again.

Important:

•Do not keep displaying a still picture for an extended period of time, as the afterimages may linger on the screen.

Page-up and page-down

You can go up and down the pages of a presentation projected from a computer using the remote control. Switch the pages using the PAGE UP or DOWN button on the remote control.

Connection

To manipulate images projected from the computer using the remote control, connect the projector with the computer as shown below.

•When the projector is connected with the computer via the USB port, the "Page up/down" function works if the computer supports the USB connection as a standard feature. (In some cases, it may not work.)

•"Page up/down" function when connecting with the USB cable cannot be supported in the Macintosh computer.

•Wait for the lamp to light up before connecting the USB cable.

•When the projector is connected using a longer cable, the image may not be projected correctly.

•When you use a longer cable, the use of the repeater is recom- mended.

USB	USB 4-pin
	(type B)
USB cable	to USB port
(option)
	USB 4-pin
	(type A)

Password function

This projector provides the password function that is intended to pre- vent wrong operations by children and set controlled access for speci- fied users.

DISPLAY INPUT ............When the projector is turned on, the star-

tup screen (or splash screen) appears and stays on the screen until the password is entered. When the password is entered, the startup screen switches to the regular operation screen.

MENU ACCESS ............All the buttons except for the POWER but-

ton on the projector are disabled. (The buttons on the remote control are enabled.) You can use this mode to pre- vent wrong operations by children and set controlled access for specified users.

SPLASH ID SCREEN....IMAGE CAPTURE and SPLASH

SCREEN in the menu become unselect- able. SPLASH SCREEN is set to ON automatically.

To enable the password function:

1.Display the FEATURE menu.

2.Press the S or T button to select PASSWORD FUNCTION.

3.Press the W or X button to change the mode among DISPLAY INPUT , MENU ACCESS and SPLASH ID SCREEN .

•When the password has already been set, the mode never changes. Press the ENTER button to cancel the password function and try again.

4.Press the ENTER button.

•The screen for setting the password function appears.

opt.

FEATURE

MENU ACCESS

LOCK	OK
UNLOCK	OK

ENGLISH

EN-23